IPM BalancedPower II-S 15 kVA Скачать руководство пользователя страница 43

Страница: 43 / 69

Section III
Operation

Page 3.28

II S, 3.00

08/96

optional Windows-based UPS Manager
Plus

software. BCM Proto

enables

communications with optional OnliNet
network power management software.

27. Pressing

will select the desired

program and will bring back the previous
COM1 screen.

28. Press

once to get this screen. If your

wish to change the Com 1 baud rate,

press

to increase baud rate from 2400

to 9600, or press

to decrease from

9600 to 2400. Pressing

will display

the “Save Change?” screen.

29. Pressing

will select the desired baud

rate and will bring back the previous
COM 1 screen.

30. Press

and

to proceed.

31. Press

to obtain this screen.

32. Press

to obtain this screen. Pressing

at this point will reset the optional

COM2 serial port (see Note 1).

33. Press

once to obtain one of the “Com

2 Display” screens. Press

obtain another of these three screens, as

desired. Pressing

will display the

“Save Change?” screen. User Interface
enables the UPS to communicate in a
standard ANSI terminal format (VT100
emulation or equivalent). P–Rec Proto
allows computer-to-computer

Com 1 Display

BCM Proto

Save Change?

Yes=UP No=DN

Com 1 Baud Rate

2400

Save Change?

Yes=UP No=DN

Return to

COM 2 Menu

COM2 Device

UP to reset

Power Up Init.

Com2 Display

User Interface

Com 2 Display

P – Rec Proto

Содержание BalancedPower II-S 15 kVA






































































Результаты поиска

Содержание BalancedPower II-S 15 kVA

Отзывы:

Похожие инструкции для BalancedPower II-S 15 kVA

Бренды по названию

Популярные бренды

IPM BalancedPower II-S 15 kVA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание BalancedPower II-S 15 kVA

Отзывы:

Похожие инструкции для BalancedPower II-S 15 kVA

Бренды по названию

Популярные бренды