INVT MH860 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 125

background image

MH860 series hydraulic servo drive

Safety precautions

2

animals to avoid scalding.

4. The external braking resistor may rise to a high temperature when

the motor is frequently braked, which requires well-ventilated heat
dissipation. It is recommended to place the motor outside the
control cabinet (such as at the top ventilator outlet) with reliably
protection measures. When the motor must be installed inside the
cabinet, install it near the top ventilator outlet and away from other
components.

5. Check all external wiring carefully before first power-on to avoid

major accidents caused by incorrect wiring.

6. Turn on the motor for the first time with no load if possible, and

make ready to turn off it depending on the running conditions.

7. Do not close or open the power supply, but enable or disable the

setup to start or stop the servo system.

8. The product contains electrolytic capacitors, integrated circuits,

epoxy boards and other components. Dispose of a scrap product
as industrial waste; otherwise, personal injury or environmental
pollution may be caused.

Note

1. Protect the drive against physical shock or vibration during the

delivery and installation. Do not carry the drive only by its front
cover as the cover may fall off.

2. Prevent the screws, cables and other conductive parts from falling

into the drive.

3. R, S and T are the power input terminals, while U, V and W are

the output motor terminals. Connect the input power cables and
motor cables properly; otherwise, damage to the drive may occur.

4. Close the drive front cover or junction box before using the drive;

otherwise, electric shock may occur.

5. Use proper torque to tighten screws for installation and wiring.

6. Do not carry out insulation voltage-endurance test on the drive, or

measure the control circuits of the drive with a megohmmeter.

For workplaces where the occasional failure of product could cause a major accident or
significant damage, please consider equipment safety separately.

The manufacturer, seller, and service provider shall not be liable or responsible for associated

damages and joint liability due to servo system failure.

«
...
5
6
7
8
9
...
»

Содержание MH860 Series






























































































































Отзывы:

Нет отзывов

Похожие инструкции для MH860 Series

Бренд: Inovance Страницы: 42

Бренд: Harmonic Drive Страницы: 26

Бренд: SCHUNK Страницы: 36

Бренд: Leadshine Technology Страницы: 14

Allen-Bradley 35E

Бренд: Rockwell Automation Страницы: 226

Бренд: BFT Страницы: 2

Targo R-5024-400

Бренд: Alutech Страницы: 56

Targo TR-3531-230

Бренд: Alutech Страницы: 60

Бренд: Applied Motion Products Страницы: 44

Бренд: ICAN Страницы: 16

Бренд: ABB Страницы: 40

VLT PROFINET MCA 120

Бренд: Danfoss Страницы: 8

Бренд: Panasonic Страницы: 26

VLT Panduan Cepat

Бренд: Danfoss Страницы: 25

Бренд: Becker Страницы: 8

Бренд: Becker Страницы: 16

Бренд: Becker Страницы: 28

Бренд: Franklin Electric Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды