Invivo Millennia 3155A, Руководство по обслуживанию, Страница: 48 / 76

5-6
NOTE
After a radio’s communication data rate has been changed (Set Data Rate code “sd” above),
the radio will then expect all further communication to proceed at the new data rate. Therefore,
the programmer must alter the “BaudRate” value in the radio configuration window or
Com24
(depending on which radio programming method is in use) to correspond with the new rate
programmed into the radio (Remote 083=9600bps; Base 083=9600bps). When, and ONLY
when, the data rate programmed into the radio transceiver has been changed, change the
“BaudRate” value to match the new data rate just programmed into the radio transceiver (if
using
Com24 , do
NOT
disconnect the test fixture from the pc or HE60 transceiver). Type the
query: sd? <Enter>, and verify that the screen echoes the new data rate programmed into the
radio transceiver on the next line on the screen.
c. Enter all required NETWORK COMMANDS as follows:
3150 Series 3155 Series AS164 AS164A AS163 PMU
Command (BASE) (REMOTE) (BASE) (REMOTE) (REMOTE) DESCRIPTION
wn ____ ____ ____ ____ ____ Set Network Number (0 thru f)
wb 1 0 1 0 0 Set Base=1/ Remote=0
wd 44 AA AA AA AA Set Destination Address (never
use ff)
ws 88 AA 88 AA 55 Set Source Address (never use
ff)
wt 1 1 1 1 1 Set Channel Access Mode
(0=CSMA/1=TDMA)
wp 1 1 1 1 1 Set Transmit Power (0=low
power/1=hi power)
d. Enter all required SERIAL INTERFACE COMMANDS as follows:
3150 Series 3155 Series AS164 AS164A AS163 PMU
Command (BASE) (REMOTE) (BASE) (REMOTE) (REMOTE) DESCRIPTION
sy 0 0 0 0 0 Set 0=Asynchronous/
1=Synchronous
sd (see note) 014 083 083 083 083 Set Data Rate (083=9600 bps),
(014=57600 bps)
sp 1 0 0 0 0 Set Packet Mode (0=point-to-
point/1=multipt)
e. Enter all required PROTOCOL COMMANDS as follows:
3150 Series 3155 Series AS164 AS164A AS163 PMU
Command (BASE) (REMOTE) (BASE) (REMOTE) (REMOTE) DESCRIPTION
ph 33
16
33
16
33
16
33
16
33
16
Set Hop Duration (33
16
=6.712
msec)
pk 01 01 01 01 01 Set Minimum Packet Length
pl 24 24 24 24 24 Set Maximum Packet Length
pt 03 03 03 03 03 Set Packet Timeout Duration
pm 40 40 40 40 40 Set Link Margin
pr 10 10 10 10 10 Set ARQ Attempt Limit
py 02 02 02 02 02 Set ARQ Per-Hop Limit
pb 08 08 08 08 08 Set CSMA Backoff Constant
pp 19 19 19 19 19 Set CSMA Persistence
ps 00 00 00 00 12 Set TDMA Time Slot
pg 0 0 0 0 0 Enable Peer Addressing
(0=disable/1=enable)
px 0 0 0 0 0 Enable Redundant Transmit
(0=disable/1=enable)
pe (see note) 0 0 0 0 0 Enable Limited ETSI Channel
Set (0=disable/1=enable)
pd 0 0 0 0 0 Antenna Diversity
(0=disable/1=enable)