Version 1.00
| Optidrive CoolVert User Guide |
29
www.invertekdrives.com
4
Set-up and Operation
Par
Description
Display Range
Note
Comms
Register
P0-01 Analog input value
-100.0 …100.0%
1dp, 0.0%~99.9% or 100%
20
P0-03 Digital input status
Binary:
00 ... 11 (Drive input)
Drive terminal input result (MSB = Digital input 1, LSB = AI1) 11
P0-04 Speed controller reference
- P1-02 … P1-01
600 = 60.0rps with one decimal place
40
P0-05 Internal temperature
°C
No decimal place
39
P0-07 Speed ref via communications
- P1-02 … P1-01
600 = 60.0rps with one decimal place
-
P0-08 User PI reference
0.0%…100%
1= 0.1%, 0.0% ~ 99.9% or 100%
-
P0-09 User PI feedback
0.0%…100%
1= 0.1%, 0.0% ~ 99.9% or 100%
-
P0-10 User PI output
0.0%…100%
1= 0.1%, 0.0% ~ 99.9% or 100%
-
P0-11 Applied motor voltage
V rms
No decimal place, 1 = 1V
43
P0-13 Trip log
Recent 4 trips with time
tag
Four entries each with the trip code and the time stamp
-
P0-14 Magnetising current (Id)
A (rms)
Current shown with one decimal place
-
P0-15 Torque producing current (Iq)
A (rms)
Current shown with one decimal place
-
P0-16 Off time count down time
s
Displays the time remaining before the drive will be
permitted to start as a consequence of the setting in P2-10
-
P0-17 On time count down time
s
Displays the time remaining before the drive will be
permitted to stop as a consequence of the setting in P2-11
-
P0-18 Restart delay count down time
s
Displays the time remaining before the drive will be permitted
to re-start as a consequence of the setting in P2-12
-
P0-19 Crankcase Heating Current
A
Displays the actual current injected into the motor during the
crankcase heating operation
-
P0-20 DC bus voltage
V dc
No decimal place. 100 = 100V
23
P0-21 Heatsink temperature
Degrees C (calculated) No decimal place. 10 = 10°C
24
P0-22 DC bus voltage ripple
V rms
No decimal place. 100 = 100V
-
P0-23 Time accumulated above 85◦C
(H/sink)
Display in hours and
minutes
-
P0-24 Time accumulated above 80◦C
(ambient)
Display in hours and
minutes
-
P0-25 Rotor speed
rps
600 = 60.0rps with one decimal place
-
P0-26 kWh meter
0.0 … 999.9 kWh
One value only
32
P0-27 MWh meter
0.0 … 65535 MWh
One value only
33
P0-28 Software version and checksum
Eg
“IO 1.00 326B”
“PS 1.00 526E”
Two entries
First is IO version and checksum (no checksum over
Modbus)
Second is DSP version and checksum (no checksum over
Modbus)
-
15
16
P0-29 Drive type
Size info, input voltage,
power rating, Output
phases, drive type etc
Four entries over Modbus
First is frame size and input voltage level, as “F2 230”
Second is power rating, as “ 1.5” or “HP 10”
Third is output phase number, as “3P-out”
Fourth is the drive ID
-
12
13
14
17
P0-30 Drive Serial number
Unique drive identifier
fixed during production
Four entries over Modbus to make up the serial number
25
26
27
28
P0-31 Hours run since date of
manufacture
Display in hours and
minutes
Two entries over Modbus - First is Hour
Second is minute and second
34
35
P0-32 Run time since last trip (1)
Display in hours and
minutes since last trip
-
P0-33 Run time since last trip (2)
Display in hours and
minutes since previous
trip
-
