Invertek Drives 3-440300-3F12-TN Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 76

background image

70

| Optidrive Eco User Guide |

Version 3.07

www.invertekdrives.com

11.6. Additional Information for UL Compliance

Optidrive Eco is designed to meet the UL requirements. For an up to date list of UL compliant products, please refer to UL listing
NMMS.E226333. In order to ensure full compliance, the following must be fully observed.

Input Power Supply Requirements

Short Circuit Capacity

All the drives in the Optidrive Eco range are suitable for use on a circuit capable of delivering not

more than 100kA rms (AC) short-circuit Amperes symmetrical with the specified maximum supply

voltage when protected by UL type J, T or CC fuses (exception: Eaton Bussmann FWP series must be

used for size 6A & 6B IP20 models).

Mechanical Installation Requirements

All Optidrive Eco units are intended for indoor installation within controlled environments which meet the condition limits shown in section

Environmental

.

The drive can be operated within an ambient temperature range as stated in section

11.1. Environmental

.

For IP20 units, installation is required in a pollution degree 1 environment.
For IP66 (Nema 4X) units, installation in a pollution degree 4 environment is permissible.

Electrical Installation Requirements

Incoming power supply connection must be according to section 4.4. Incoming Power Connection.
Suitable Power and motor cables should be selected according to the data shown in section

11.5. Output Power and Current ratings

and the

National Electrical Code or other applicable local codes.
Motor Cable

75°C Copper must be used.

Power cable connections and tightening torques are shown in sections

3.7. Mounting the Drive – IP20 Units

3.9. Guidelines for Mounting (IP66

3.8. Guidelines for Mounting (IP55 Units)

.

Integral Solid Sate short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance

with the National Electrical Code and any additional local codes. Ratings are shown in section

11.5. Output Power and Current ratings

.

UL Listed ring terminals / lugs must be used for all bus bar and grounding connections.

General Requirements

Optidrive Eco provides motor overload protection in accordance with the National Electrical Code (US).



Where a motor thermistor is not fitted, or not utilised, Thermal Overload Memory Retention must be enabled by setting P4-12 = 1.



Where a motor thermistor is fitted and connected to the drive, connection must be carried out according to the information shown in section

9.3. Parameter Group 4 – High Performance Motor Control

For Canadian Installations:

Transient surge suppression shall be installed on the line side of this equipment and shall be rated as shown below, suitable for over voltage

category III and shall provide protection for a rated impulse withstand voltage peak of 2.5kV.

Supply Voltage Rating of the Drive

Phase-Phase Surge Protection

Voltage Rating

Phase-Ground Surge Protection

Voltage Rating

200 - / - 10%

230VAC

230VAC

380 - / - 10%

480VAC

480VAC

500 - / - 10%

600VAC

600VAC

11

Technical Data

«
...
68
69
70
71
72
...
»

Содержание 3-440300-3F12-TN













































































Отзывы:

Нет отзывов

Похожие инструкции для 3-440300-3F12-TN

Бренд: Calpeda Страницы: 22

Бренд: Danfoss Страницы: 54

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 197

Бренд: Danfoss Страницы: 284

Бренд: Danfoss Страницы: 53

BA-Intellidrive BAI 10

Бренд: Aerotech Страницы: 202

Бренд: REDEX ANDANTEX Страницы: 28

Бренд: Bosch Страницы: 50

Бренд: Bosch Страницы: 66

rexroth Servodyn-D

Бренд: Bosch Страницы: 72

MSK030B NSNN Series

Бренд: Bosch Страницы: 178

MSK030B-0900-NN

Бренд: Bosch Страницы: 282

Бренд: Toshiba Страницы: 13

Бренд: Toshiba Страницы: 15

Бренд: Toshiba Страницы: 14

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды