manualshive.com logo in svg

Invacare Top End Excelerator XLT, Руководство владельца по эксплуатации и техническому обслуживанию, Страница: 33 / 64

Поделиться
Скачать
Invacare Top End Excelerator XLT Скачать руководство пользователя страница 33

Part No. 1114850

33

Excelerator™ XLT Series

BACK ANGLE ADJUSTMENT (FIGURE 6)

1. If installed activate parking brake.
2. Loosen, but do not remove the four (4) rear socket screws that secure the seat

frame to the handcycle frame.

NOTE: There are two (2) socket screws on the right and left side of the handcycle.

3. Loosen, but do not remove the hex bolts and locknuts that secure the two (2) seat

angle adjustment clamps to the rear seat supports.

NOTE: There is one (1) clamp on the right and left side of the handcycle.

4. Perform one (1) of the following:

A.

INCREASING BACK ANGLE

 - While lifting up on the back support tubes,

pull the seat upward to the desired position.

B.

DECREASING BACK ANGLE

 - While pushing down on the back support

tubes, push the seat down to the desired position.

5. Tighten the three (3) socket screws that secure the seat frame to the handcycle

frame securely.

6. Tighten the hex bolts and locknuts that secure the two (2) seat angle adjustment

clamps to the rear seat supports securely.

Socket Screws

Handcycle Frame

Seat

FIGURE 6 - BACK ANGLE ADJUSTMENT

Seat Angle

Adjustment

Clamps

SECTION 5

RIDING 

POSITION

RIDING POSITION

Back Support

Tube

All manuals and user guides at all-guides.com

Содержание Top End Excelerator XLT

































































Отзывы:

Нет отзывов