manualshive.com logo in svg

Invacare Top End Excelerator XLT, Руководство владельца по эксплуатации и техническому обслуживанию, Страница: 22 / 64

Поделиться
Скачать
Invacare Top End Excelerator XLT Скачать руководство пользователя страница 22

Excelerator™ XLT Series

22

Part No. 1114850

4. Ensure the footrest is adjusted properly. If necessary, adjust the footrest. Refer to FOOTREST

AND LEG GUARD REPLACEMENT in SECTION 5 of this manual.

NOTE: Footrest should be adjusted so that when seated with feet in the footrests, there is a slight bend at the

knee.

5. Ensure the seat is adjusted properly. If necessary, adjust the seat. Refer to SEAT

ADJUSTMENT in SECTION 5 of this manual.

NOTE: Seat should be adjusted so that when seated with feet in the footrests, there is a slight bend at the knee

and a slight bend at the elbow when the hand crank is furthest away.

6. If installed, release the parking brake. Refer to PARKING BRAKE in this section of the manual.

WARNING

At least one (1) hand MUST be on the hand crank assembly at all times.

Otherwise, injury or damage may occur.

7. Place at least one (1) hand onto the hand crank.

NOTE: The hand crank assembly is used for propelling and steering of the handcycle.

8. Rotate (pedal) the hand crank FORWARD (toward the front) to propel the handcycle

forward.

9. EXCELERATOR XLT AND XLT JR. MODELS ONLY - Rotate (pedal) the hand crank

BACKWARD (toward the rear) to apply the brake and slow down or stop.

SHIFTING GEARS

SEVEN (7) SPEED HUB (FIGURE 2)

NOTE: This procedure applies to the Excelerator XLT and XLT Jr. ONLY.

To shift gears while moving, hold onto the hand crank assembly with one (1) hand,

continue pedaling, but ease pressure on the pedals and select the gear required with the

other hand. When the Excelerator XLT is stationary, simply select gear required.
1. Perform one (1) of the following:

A.

UPSHIFT - 

Push the shifting lever towards the indicator and release. Repeat

until the desired gear is achieved.

B.

DOWNSHIFT - 

Push shifting lever down and away from the indicator. Repeat

until the desired gear is achieved.

FIGURE 2 - SHIFTING GEARS

UPSHIFT

DOWNSHIFT

Shifting Lever

Indicator

SECTION 4

OPERATION

OPERATION

All manuals and user guides at all-guides.com

Содержание Top End Excelerator XLT

































































Отзывы:

Нет отзывов