Invacare Perfecto 2 IRC5P Скачать руководство пользователя страница 63

Страница: 63 / 88

SECTION 17—ON/OFF SWITCH

Part No 1148070

Perfecto

™

SECTION 17—ON/OFF SWITCH

Replacing On/Off Switch

DANGER

To prevent electrical shock, ALWAYS disconnect concentrator from electrical outlet
before servicing.

NOTE: For this procedure, refer to FIGURE 17.1 on page 63.

1. Unplug unit.

2. Remove cabinet. Refer to Removing Cabinet on page 23.

3. Remove control panel. Refer to Removing Control Panel on page 54.

4. Remove and code the four spade connectors from back of existing On/Off switch.

5. Compress retaining grips on back of existing On/Off switch and push switch out

through front of control panel.

NOTE: Ensure proper orientation of the On/Off

(

)

switch and wiring connections before

installation. Refer to FIGURE 17.1, Detail “A” and Detail “B” below.

CAUTION

DO NOT install the On/Off (I/O) switch upside down. Universal Off (O) symbol should
be at bottom and Universal On (I) symbol should be at the top. Possible damage to the
concentrator may result if not properly installed.

6. Reverse STEP 4 to secure new On/Off (

)

switch.

7. Reinstall control panel. Refer to Removing Control Panel on page 54.

8. Reinstall cabinet. Refer to Removing Cabinet on page 23.

FIGURE 17.1

Replacing On/Off Switch

I/O

On/Off

(

)

Switch

I/O

DETAIL “A”

OFF

DETAIL “B”

Spade Connector

from Brown Wire

attached here

Brown Jumper

Wire (From

Circuit Breaker)

On/Off

(

)

Switch

I/O

Spade Connectors
from White Wires

attached here

Front View

Back View

Содержание Perfecto 2 IRC5P

























































































Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды

Invacare Perfecto 2 IRC5P, Руководство по обслуживанию

Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды