Invacare Perfecto 2 IRC5P Скачать руководство пользователя страница 17

Страница: 17 / 88

SECTION 4—TROUBLESHOOTING

Perfecto

™

Power Loss:
(Continued)
Internal Status Indicators:
RED: Off
GREEN: Off
Unit plugged in, power
switch, alarm off. Battery
Free circuit drained

P.C. board.

a. P.C. board damaged.

b. Loose or damaged connector.

a. Replace

P.C. Board. Refer to

Replacing P.C. Board on page 59.

b. Repair or replace connector.

Internal Power
Loss Senso

Internal Status Indicators:
RED: Off
GREEN: Off
Alarm may or may not be on.
Control Panel Indicators:
RED: Off
YELLOW: Off
GREEN: Off
Fan operates, Compressor
not operating.

Transformer assembly.

a. Faulty.

b. Connector loose or

disconnected.

c. Faulty wiring.

a. Replace. Refer to Replacing the

Transformer on page 62.

b. Reattach connector.

c. Replace transformer assembly. Refer

to Replacing the Transformer on
page 62.

P.C. board faulty.

Replace P.C. board. Unit requires retiming
after P.C. board replacement. Refer to
Replacing P.C. Board on page 59.

High Pressure:
Internal Status Indicators:

RED: One Flash
GREEN: Two Flashes

Unit plugged in, power switch
on, continuous alarm.
Compressor shut down.

P.C. board:

a. Malfunction

b. Disconnected wire.

c. Shifting valve at pressures greater

than 25 p.s.i. for Perfecto2.

a. Set flow to max L/min. for

concentrator. Check voltage across

Pilot Valve 1 on 200 volt scale. If

meter reads 0 volts when unit is

turned on, replace P.C. board

b. Check spade connectors on pilot

valves 1 or 2 and connectors on P.C.

board.

c. Replace P.C. board. Unit requires

retiming after P.C. board

replacement. Refer to Replacing P.C.

Board on page 59.

4-way Valve:

a. Not shifting.

b. Bad coil.

c. Coil resistance.

a. Check voltage. If voltage rises to

approximately 24 volts D.C. when

unit shuts down, P.C. board is

functioning properly. Replace the

valve if shorted or open. Refer to

Replacing 4-Way Valve and/or

Manifold Assembly on page 66.

b. Replace 4-way valve. Refer to

Replacing 4-Way Valve and/or

Manifold Assembly on page 66.

c. Coil should read 175 ohm ± 20.

Compressor inlet filter dirty or
plugged.

Replace compressor inlet filter. Refer to
Replacing the Compressor Inlet HEPA
Filter on page 26.

SYMPTOM

PROBABLE CAUSE

SOLUTION

Содержание Perfecto 2 IRC5P

























































































Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды

Invacare Perfecto 2 IRC5P, Руководство по обслуживанию

Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды