Invacare Perfecto 2 IRC5P Скачать руководство пользователя страница 26

Страница: 26 / 88

SECTION 6—PREVENTIVE MAINTENANCE

Perfecto

™

Part No 1148070

FIGURE 6.2

Replace the Outlet HEPA Filter

Replacing the Compressor Inlet HEPA Filter

NOTE: For this procedure, refer to FIGURE 6.3 on page 27.
NOTE: Perform this procedure during preventive maintenance or between patients depending
upon the environment the concentrator is used in.

1. Unplug the unit.

2. Remove the filter access panel by pressing down on center tab and pulling panel out.

3. Grasp the compressor inlet HEPA filter, pull outward and up until filter is dislodged

from rubber base.

4. Discard the existing compressor inlet HEPA filter.

5. Install new compressor inlet filter by inserting the filter into the rubber base.

6. Push the filter down until the rubber base touches the edge of the filter.

7. Reinstall the filter access panel.

Tubing

Outlet HEPA Filter

Tubing

Содержание Perfecto 2 IRC5P

























































































Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды

Invacare Perfecto 2 IRC5P, Руководство по обслуживанию

Результаты поиска

Содержание Perfecto 2 IRC5P

Отзывы:

Похожие инструкции для Perfecto 2 IRC5P

Бренды по названию

Популярные бренды