Invacare Formula CG Elevate Скачать руководство пользователя страница 69

Страница: 69 / 95

Setup/Maintenance

7.27

Disconnecting/Connecting the CMPJ+

Joysticks

The joystick connector is located at the rear of the seat
frame.

7.27.1

Connecting the CMPJ+ Joysticks

Ensure the gaskets

are installed in the top connector cap

and between network connectors

Ensure the latch is pulled away from the network connector.

Connect the network connector to the other connectors.

Top

and Bottom

Connectors - Install connector caps onto

the network connector.

Push the latch in to secure the network connectors and caps.

If necessary secure excess cable using tie-wraps.

7.27.2

Disconnecting the CMPJ+ Joysticks

Pull the latch

away from the joystick connector.

Disconnect the joystick connector from the remaining
connectors.

7.28

Replacing Seat Positioning Strap

1143155-R-01

Содержание Formula CG Elevate
































































































Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды

Invacare Formula CG Elevate, Руководство пользователя

Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды