Invacare Formula CG Elevate Скачать руководство пользователя страница 63

Страница: 63 / 95

Setup/Maintenance

7.18.2

Angle Adjustment

Observe the angle of the footplate for reinstallation.

The settings for positioning the footplates on the half-clamps
may vary for each footplate.

Loosen, but DO NOT remove, the two flat screws

, washer

and locknuts

that secure the footplate

to the half clamp

Position the footplate to the necessary angle to accommodate
the user.

Retighten the two flat screws, washers and locknuts.

7.18.3

Perpendicular and/or Inversion/Eversion

Adjustment

It is not necessary to remove the footplate to perform this
adjustment.

Insert a flathead screwdriver through the half clamp

on the

footplate.

Slowly turn nylon adjustment screw

in or out until footplate is

perpendicular to the footrest assembly or the desired inversion
or eversion is obtained.

7.19

Adjusting the Height of the Manual Center

Mount Footrest

1143155-R-01

Содержание Formula CG Elevate
































































































Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды

Invacare Formula CG Elevate, Руководство пользователя

Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды