manualshive.com logo in svg

Intergraph Fibre Channel, Руководство пользователя, Страница: 77 / 84

Поделиться
Скачать
Intergraph Fibre Channel Скачать руководство пользователя страница 77

Installation

3

1.1.2

FC-AL Front Dummy Fascias

FC-AL front dummy fascias are provided for fitting in all unused drive bays. They are designed as integral drive 

module front caps with handles and must be fitted to all unused drive bays to maintain a balanced air flow.

1.1.3

Anti-tamper Locks

Anti-tamper locks are provided to disable the normal ’Push/Push’ latch action of the carrier handle.

1.2 Planning and Configuring Your Installation 

1.2.1

System Configuration

Before you begin installation you should become familiar with the configuration requirements of your SS-1200-

FCAL system.

Please refer to the SS-1200-FCAL Installation/User Guide for information on your overall system configurations. 

When planning your system configuration, please remember that:

• All SS-1200-FCAL enclosure drive bays must be filled with either a drive carrier, front dummy fascia or ESI 

/Ops Panel module (Bay 1/1 only), no bays should be left completely empty.

The correct positions of each of the optional plug-in modules are detailed in the SS-1200-FCAL Installation/User 

Guide.

1.2.2

Drive Configuration

Important

After you have installed the drive carrier modules in your SS-1200-FCAL enclosure, please refer 
to the SS-1200-FCAL LRC I/O Module Installation Guide for configuration information relevant to 
the I/O module and instructions for setting the Drive Select ID bits.

Although it is not essential we recommend that if there are only a limited number of drives or PSUs fitted then they 

should be located as close together as possible (If for example only 1 PSU and 6 drives are fitted, the PSU should 

be in rear bay 2 and the drives in Bays 1/1 through 2/3).

1.2.3

Drive Auto Start

The delayed sequence start is used to start the drives in the enclosure unless the Manual Start Flag (Jumper) is fitted, 

in which case no drives will start and start up is left to the host computer.

If this is the case then to guarantee maximum redundancy within the system it is important that the host computer 

starts the disks in a manner which gives the smoothest loading to the power system. The maximum number of drives 

which can be started concurrently in a 12 drive enclosure are defined in 

Table 1–1

If there are more than the specified number of drives installed as detailed in 

Table 1–1

, then the drives should be 

started in a staggered sequence at approximately 12 second intervals.

Содержание Fibre Channel





















































































Отзывы:

Нет отзывов