manualshive.com logo in svg

Intergraph Fibre Channel, Руководство пользователя, Страница: 73 / 84

Поделиться
Скачать
Intergraph Fibre Channel Скачать руководство пользователя страница 73

Preface

v

European Regulations

When installed in the SS-1200 chassis, this equipment complies with all applicable European Regulations.

Safety

Warning

To ensure safe and correct operation of the drive carrier modules installed in a Salient subsystem 
all safety precautions and instructions referred to in this installation guide must be followed 
thoroughly.

The plug-in drive carrier modules and FC-AL link modules are part of the fire enclosure and must 
only be removed when a replacement can be immediately added. The Salient subsystem must not 
be run without all units in place.

Moving and Handling 

Disk drives are very susceptible to physical shock but damage may not be immediately obvious.

Please observe the following precautions before moving and handling the enclosure:

• Always spin down drives prior to removing from the enclosure.

• If the Salient enclosure has been installed in a 19 inch rack which is to be moved, remove all drives and other 

plug-in modules and repackage before transporting them separately.

• Keep all plug-in modules packaged to protect them until they are required for installation

• Take care not to drop any of the plug-in modules or strike them onto a hard surface.

Data Security

• Power down your host computer and all attached peripheral devices before beginning installation.

• Each Salient enclosure contains up to 12 removable disk drive modules. Disk drives are fragile. Handle them 

with care, and keep them away from strong magnetic fields. 

• All the supplied units and blanking plates must be in place for the air to flow correctly around the enclosure 

and also to complete the internal circuitry. 

• If the subsystem is used with plug-in units or blanking plates missing for more than a few minutes, the 

enclosure can overheat, causing power failure and data loss. Such use may also invalidate the warranty. 

• If you remove any drive module, you may lose data. 

– If you remove a drive module, replace it immediately. If it is faulty, replace it with a module of the same 

type and capacity 

• Ensure that all drive modules are removed from the enclosure before attempting to handle or move the rack 

installation.

• Do not abandon your backup routines. No system is completely foolproof.

Содержание Fibre Channel





















































































Отзывы:

Нет отзывов