Intergraph Fibre Channel Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 84

Intergraph Fibre Channel Скачать руководство пользователя страница 33

Getting Started

23

2.3.8.1

Parts Check List

where applicable:

• Single bay Rear Blank plates

• 1x2 bay Rear Blank plates

• 1x3 bay Rear Blank plates

Warning

Operation of the enclosure with

ANY blank plates or rear modules missing will disrupt the airflow

and the drives will not receive sufficient cooling. It is

ESSENTIAL that all rear apertures are filled

before operating the unit.

2.3.8.2

Procedure

Clip the correct size blank plates into the rear bay apertures as required.

2.3.9

Power Cord Connection

Warning

Ensure that you select the correct voltage range

on the Power Supply/Cooling module BEFORE

connecting the power cords. The Power supplies are

NOT auto-ranging, failure to select the

correct range

WILL damage the PSU.

2.3.9.1

Parts Check List

• Trifurcated power cord

• Power cord to requisite local standards

2.3.9.2

Procedure

1

Attach the Triifurcated power cord to the Power Supply/Cooling Modules,

2

Attach the power cord to the in-line IEC connector in this cord.

Caution

These power splitting cables are provided so that the system is operated from a SINGLE power source
thus providing a single point of disconnect. They must always be used. Do not connect to the Power
source until installation is complete.

3

A STANDBY LED on the ESI/Ops panel indicates whether AC mains power is present.

Caution

The power connections must always be disconnected prior to removal of the Power Supply/Cooling
module from the enclosure.

The On/Off switches on each Power Supply/Cooling module Only isolate the power from that module.
Any other power supply/cooling modules will remain active.

2.3.10

Grounding Checks

Perform these checks to ensure that a safe grounding system is provided.

• If a rack distribution system is being used.

– Ensure power is removed from the rack.

– Connect the SS-1200-FCAL power cord to the rack distribution and the enclosure.

• If a direct connection is made with the SS-1200-FCAL power cord, ensure that it is connected to the enclosure.

Warning

Some electrical circuits could be damaged if external signal cables or power control cables are
present during the grounding checks.

• Check for continuity between the earth pin of the IEC 320 connector on one of the Power Supply /Cooling

modules and any exposed metal surface of the SS-1200-FCAL enclosure.

«
...
31
32
33
34
35
...
»

Содержание Fibre Channel





















































































Отзывы:

Нет отзывов