IntelliQuip TOUGHPOWER TP-1000, Руководство пользователя

Страница: 14 / 35

ToughPower. Charging of the Battery will only occur when the Vehicle is running or the Car Key is in the
“Accessories”
​ ​
position.
The
​ ​
LCD
​ ​
display
​ ​
will
​ ​
show
​ ​
that
​ ​
the
​ ​
battery
​ ​
is
​ ​
being
​ ​
charged
​ ​
from
​ ​​
CAR
​​ ​
input.
The internal 10 Amp DC-DC “Multi-Stage” Charger will receive
and regulate the power to charge the Battery fitted in the
ToughPower. The multi-stage charger is current limited and
cannot draw more than 10 Amps of power. It will charge and
condition the Battery, and will shut-off when charging is
complete.
Note:
​
The current will not exceed 10 Amp through your Vehicle
CIG
​ ​
Socket.
Warning: It is recommended that the vehicle CIG Socket
​
must be ignition controlled so that it is only
powered when the vehicle is in “Accessories” mode or running. Check this with your vehicle manufacturer
or
​ ​
local
​ ​
service
​ ​
provider
​ ​
otherwise
​ ​
you
​ ​
run
​ ​
the
​ ​
risk
​ ​
of
​ ​
discharging
​ ​
your
​ ​
car’s
​ ​
main
​ ​
battery.
7.3
​ ​​ ​
Solar
​ ​
Power
​ ​
Charging
​ ​
–
​ ​
(SOLAR)
​ ​​
12V
​ ​
Nominal
​ ​
Solar
​ ​
Panels
​ ​
only
The ToughPower can accept Regulated and Unregulated Solar
Power
​
12V Nominal Solar Panels only
​
. When Unregulated
Solar Panels are connected the internal electronics
automatically detect this and will switch to MPPT Controller
mode.
12V
​ ​​
Nominal
​​
​
Solar
​ ​
Panels:
Max
​ ​
Voc
​ ​
=
​ ​
25V
The TP-1000
​
DUAL
is supplied with a 2-Pin Accessory Cable.
Connect the 2-Pin Plug into the ToughPower then connect the
bare ends to your Solar Panel using your preferred connector.
Note:
​​ ​
Check
​ ​
the
​ ​
Polarity
​ ​
of
​ ​
your
​ ​
connections!
The TP-600 & TP-1000 are supplied with a 4-Pin CIG Plug Accessory Cable. This same Accessory Cable is
used for both Car Charging and Solar Charging. To enable you to swap between the two charging options,
it is recommended you attach a female CIG Socket to your Solar Panel, then simply connect the 4-Pin Plug
into the ToughPower and connect the CIG Male Plug end into your Solar Panel female CIG Socket.
​
Note:
Check
​ ​
the
​ ​
Polarity
​ ​
of
​ ​
your
​ ​
connections!
WARNING:
​ ​
Great
​ ​
care
​ ​
must
​ ​
be
​ ​
taken
​ ​
when
​ ​
attaching
​ ​
connectors
​ ​
to
​ ​
ensure
​ ​
the
​ ​
polarity
​ ​
is
​ ​
correct!
The
​ ​
LCD
​ ​
display
​ ​
will
​ ​
show
​ ​
that
​ ​
the
​ ​
battery
​ ​
is
​ ​
being
​ ​
charged
​ ​
from
​ ​​
SOLAR
​​ ​
input.
Page
​ ​
14