Intel D815EEA2 страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 96

background image

Updating the BIOS

55

Recovering the BIOS

It is unlikely that anything will interrupt the BIOS update, however, if an interruption occurs, the
BIOS could be damaged. The following steps explain how to recover the BIOS if an update fails.
The following procedure uses recovery mode for the Setup program. See page 48 for more
information on Setup modes.

✏

NOTE

Because of the small amount of code available in the boot block area, there is no video support.
You will not see anything on the screen during this procedure. Monitor the procedure by listening
to the speaker and looking at the diskette drive LED.

1. Turn off the computer, disconnect the computer’s power cord, and disconnect all external

peripherals.

2. Remove the computer cover and locate the configuration jumper block (J9G2) (see Figure 26).
3. Remove the jumper from all pins as shown below to set recovery mode for Setup.

1

3

4. Insert the bootable BIOS update diskette into diskette drive A.
5. Replace the computer cover, connect the power cord, turn on the computer, and allow it to

boot. (The recovery process will take a few minutes. Listen to the speaker and watch for
drive A activity.)

•

Upon applying power, drive A will begin to show activity. In about a minute, two beeps
are heard and drive A activity ceases (temporarily) indicating the successful recovery of
the BIOS core. Drive A activity will begin again followed by two more beeps indicating
the successful recovery of the boot block. This sequence of events indicates that
successful BIOS recovery has taken place.

•

A series of continuous beeps indicates that BIOS recovery has failed.

6.  If recovery fails, return to step 1 and repeat the recovery process.
7.  If recovery is successful, turn off the computer, and disconnect its power cord.
8.  Remove the computer cover and continue with the following steps.
9.  On the jumper block (J9G2), reinstall the jumper back on pins 1-2 as shown below to set

normal mode for Setup.

1

3

10. Leave the update diskette in drive A, replace the computer cover, and connect the computer’s

power cord.

11. Turn on the computer and continue with the BIOS update (see page 53).

«
...
53
54
55
56
57
...
»

Содержание D815EEA2

































































































Отзывы:

Нет отзывов

Похожие инструкции для D815EEA2

Бренд: Paradyne Страницы: 22

Univerge SV9300

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 20

DS2000 IntraMail

Бренд: NEC Страницы: 2

Бренд: Harman Kardon Страницы: 66

Бренд: Observint Страницы: 117

Бренд: M86 Security Страницы: 46

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: Idis Страницы: 85

Бренд: IDT Страницы: 207

Бренд: Lanner Страницы: 59

Бренд: PaloAlto Networks Страницы: 28

Бренд: Magma Страницы: 2

Бренд: Cypress Semiconductor Страницы: 15

Wisenet PRN-6400DB4

Бренд: Hanwha Techwin Страницы: 125

Бренд: WTI Страницы: 178

Бренд: ADLINK Technology Страницы: 95

Бренд: WatchNet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды