Intel D815EEA2 Скачать руководство пользователя страница 10

Страница: 10 / 96

Intel Desktop Boards D815EEA2, D815EPEA2, D815EFV, and D815EPFV Product Guide

Table 2.

Feature Summary

(continued)

Characteristic Specification

Video

•

The D815EEA2 and D815EFV boards include:



Intel 82815E integrated graphics support



AGP universal connector supporting 1x, 2x, or 4x AGP cards or a Graphics

Performance Accelerator (GPA)



Rear panel VGA connector

•

The D815EPEA2 and D815EPFV boards include an AGP universal connector
supporting 1x, 2x, or 4x AGP cards

Peripheral
Interfaces

•

Two serial ports: one back panel and one internal connector

•

Four USB ports: four back panel and two optional front panel

•

One parallel port

•

Two IDE interfaces with Ultra DMA (33 MB/sec) and ATA-66/100 support

•

One diskette drive interface

•

PS/2

†

keyboard and mouse ports

Expansion
Capabilities

•

For D815EEA2 and D815EPEA2 boards:



Five PCI add-in card connector (SMBus routed to PCI bus connector 2,

S5 wake from PCI bus connector 2)



One AGP universal connector

•

For D815EFV and D815EPFV boards:



Three PCI add-in card connectors (SMBus routed to PCI bus connector 2,

S5 wake from PCI bus connector 2)



One AGP universal connector

BIOS

•

Intel/AMI BIOS

•

4 Mbit Firmware Hub (FWH)

•

Support for Advanced Power Management (APM), Advanced Configuration and Power
Interface (ACPI), Plug and Play, and SMBIOS

Instantly
Available
Technology

•

ACPI S3 Suspend to RAM (STR) sleep state

•

Support for

PCI Local Bus Specification

Revision 2.2

•

Wake on PS/2 keyboard and USB ports

Power
Management

Support for both ACPI Rev. 2.0 and APM Rev. 1.2

PC Design
Compliance

PC 99 and PC 99A

Hardware
Monitor

Heceta 4 supporting:

•

Remote diode temperature sense

•

Voltage sense to detect out of range values

•

Fan tachometer

SCSI LED
Connector

Allows add-in SCSI controllers to use the same LED as the onboard I/O controller

Содержание D815EEA2

































































































Результаты поиска

Содержание D815EEA2

Отзывы:

Intel D815EEA2, Руководство по эксплуатации продукта, Страница: 10 / 96

Результаты поиска

Содержание D815EEA2

Отзывы: