Intel D815EEA2 страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 96

background image

Desktop Board Features

23

Wake on LAN Technology (Optional)

CAUTION

For Wake on LAN technology, the 5-V standby line for the power supply must be capable of
providing ad5-V standby current. Failure to provide adequate standby current when
implementing Wake on LAN technology can damage the power supply.

The optional Wake on LAN technology connector can be used with PCI bus network adapters that
have a remote wake-up connector. Network adapters that are PCI 2.2 compliant assert the wake-up
signal using the PCI bus signal PME# (pin A19 on the PCI bus connectors). See Figure 30 on
page 82 for the location of the Wake on LAN technology connector on the desktop board.

Instantly Available Technology

CAUTION

For Instantly Available technology, the 5-V standby line for the power supply must be capable of
providing ad5-V standby current. Failure to provide adequate standby current when
implementing Wake on LAN technology can damage the power supply.

CAUTION

If the standby current necessary to support multiple wake events from the PCI and/or USB buses
exceeds power supply capacity, the desktop board may lose register settings stored in memory.

Instantly Available technology enables the board to enter the ACPI S3 (Suspend-to-RAM) sleep
state. While in the S3 sleep state, the computer will appear to be off. When signaled by a wake-up
device or event, the system quickly returns to its last known awake state.

The desktop board standby power indicator, shown in Figure 3, is lit when the memory modules
and PCI bus connectors have power, even when the computer appears to be off.

If the system has a dual-colored power LED on the front panel, the sleep state is indicated by the
LED turning amber. For more information about front panel LED states, see the

Intel

®

Desktop

Board D815EEA2/D815EPEA2 Technical Product Specification

or

Intel

®

Desktop Board

D815EFV/D815EPFV Technical Product Specification.

«
...
21
22
23
24
25
...
»

Содержание D815EEA2

































































































Отзывы:

Нет отзывов

Похожие инструкции для D815EEA2

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Бренд: RadiSys Страницы: 44

inLab Speedcure 9494800

Бренд: Dentsply Sirona Страницы: 91

IMACS Network Device

Бренд: Zhone Страницы: 114

iTRON B 70.2040

Бренд: JUMO Страницы: 41

OMB-DAQBOARD-500 Series

Бренд: Omega Страницы: 48

HHM Series HHM2409

Бренд: TDK Страницы: 2

Бренд: Juniper Страницы: 420

Бренд: PairGain Страницы: 80

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Бренд: Laser Страницы: 4

Бренд: Omron Страницы: 432

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды