Intel D815EEA2 страница 65 Скачать руководство пользователя

Страница: 65 / 96

Using the Setup Program

Table 16. Peripheral Configuration Submenu

(continued)

Feature Options

Description

Parallel Port

•

Disabled

•

Enabled

•

Auto (default)

Configures the parallel port.

Auto

assigns LPT1 the address 378h and the interrupt

IRQ7.

An * (asterisk) displayed next to an address indicates a
conflict with another device.

Mode

•

Output Only

•

Bi-directional
(default)

•

EPP

•

ECP

Selects the mode for the parallel port. Not available if the
parallel port is disabled.

Output Only

operates in AT

†

-compatible mode.

Bi-directional

operates in PS/2-compatible mode.

EPP

is Extended Parallel Port mode, a high-speed

bi-directional mode.

ECP

is Enhanced Capabilities Port mode, a high-speed

bi-directional mode.

Base I/O Address
(This feature is present
only when Parallel Port
is set to

Enabled

)

•

378 (default)

•

278

•

228

Specifies the base I/O address for the parallel port.

Interrupt
(This feature is present
only when Parallel Port
is set to

Enabled

)

•

IRQ 5

•

IRQ 7 (default)

Specifies the interrupt for the parallel port.

DMA Channel
(This feature is present
only when Parallel Port
Mode is set to

ECP

)

•

3 (default)

Specifies the DMA channel.

Audio Device

•

Disabled

•

Enabled (default)

Enables or disables the onboard audio subsystem.

LAN Device
(This feature is present
only when there is
onboard LAN)

•

Disabled

•

Enabled (default)

Enables or disables the LAN device.

Legacy USB Support

•

Disabled

•

Enabled

(default)

Enables or disables USB legacy support.
(See USB Support on page 18 for more information.)

Содержание D815EEA2

































































































Результаты поиска

Содержание D815EEA2

Отзывы:

Похожие инструкции для D815EEA2

Бренды по названию

Популярные бренды

Intel D815EEA2, Руководство по эксплуатации продукта

Результаты поиска

Содержание D815EEA2

Отзывы:

Похожие инструкции для D815EEA2

Бренды по названию

Популярные бренды