Intel Celeron D Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

background image

22

Intel

®

Celeron

®

D Processor in the 775-Land LGA Package

Thermal Design Guide

Order #303730

Thermal Metrology

NOTE:

Dimensions in drawing not to scale.

3.4

Processor Case Temperature Measurement
Guidelines

To ensure functionality and reliability, the Celeron D Processor in the 775-land LGA package is
specified for proper operation when T

C

is maintained at or below the thermal profile as listed in the

processor datasheet. The measurement location for T

C

is the geometric center of the IHS.

shows the location for T

C

measurement.

Special care is required when measuring T

C

to ensure an accurate temperature measurement.

Thermocouples are often used to measure T

C

. Before any temperature measurements are made, the

thermocouples must be calibrated, and the complete measurement system must be routinely
checked against known standards. When measuring the temperature of a surface that is at a
different temperature from the surrounding local ambient air, errors could be introduced in the
measurements. The measurement errors could be caused by poor thermal contact between the
thermocouple junction and the surface of the integrated heat spreader, heat loss by radiation,
convection, by conduction through thermocouple leads, or by contact between the thermocouple
cement and the heatsink base.

defines a reference procedure for attaching a thermocouple to the IHS of an FC-LGA4

processor package for T

C

measurement. This procedure takes into account the specific features of

the FC-LGA4 package and of the LGA775 socket for which it is intended.

Figure 6. Measuring T

LA

— Passive Heatsink

«
...
20
21
22
23
24
...
»

Содержание Celeron D

































































Отзывы:

Нет отзывов

Похожие инструкции для Celeron D

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Queclink Страницы: 9

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

Бренд: MC Страницы: 21

Бренд: Pressalit Care Страницы: 31

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

Бренд: National Instruments Страницы: 80

Бренд: Advantech Страницы: 108

Бренд: Idis Страницы: 18

Бренд: TANDBERG Страницы: 2

Бренд: Digisol Страницы: 73

Бренд: Rane Страницы: 6

Бренд: Valcom Страницы: 3

Бренд: Allied Telesis Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды