Intel Arria V Скачать руководство пользователя

Страница: 32 / 72

4.2.2. Configuration

The Cyclone V / Arria V SoC devices support two main type sof configuration flows:
•

Traditional FPGA configuration

•

HPS-initiated FPGA configuration

HPS-initiated configuration uses fast passive parallel (FPP) mode allowing the HPS to

configure the FPGA using storage locations accessible to the HPS such as QSPI,

SD/MMC and NAND flash. The FPGA configuration flows for the Cyclone V/Arria V SoC

are the same for the Cyclone V/Arria V FPGA devices where an external configuration

data source is connected to the control block in the FPGA.

4.2.2.1. Traditional Configuration

The traditional FPGA configuration flow is where the FPGA is configured by an external

source such as JTAG, active serial or fast passive parallel.

4.2.2.2. HPS Initiated Configuration

When the device is powered and the HPS begin executing the software in the boot

ROM, all the device I/O default to an input tri-state mode of operation. The boot ROM

configures the dedicated boot I/O based on the sampled BSEL pins.

4.2.3. Reference Materials

Refer to the following reference materials for additional information.

Related Information

•

Intel

SoC FPGA Embedded Development Suite User Guide

•

Support tab on Cyclone V SoCs

Cyclone V SoC documentation

•

Support tab on Arria V SoCs

Arria V SoC documentation

•

SoC Embedded Development Suite Getting Started Guides

•

Golden System Reference Design (GSRD) User Manuals

•

AN-709: HPS SoC Boot Guide - Cyclone V SoC Development Kit

4.3. HPS Power Design Considerations

For design considerations and recommendations on power consumption and thermal

analysis, SoC device pin connections, supply design and decoupling, refer to the Arria

V and Cyclone V Design Guidelines.

The following sections are supplemental for SoC devices.

Related Information
Arria V and Cyclone V Design Guidelines

4. Board Design Guidelines for SoC FPGAs

AN-796 | 2018.06.18

AN 796: Cyclone V and Arria V SoC Device Design Guidelines

Содержание Arria V









































































Результаты поиска

Содержание Arria V

Отзывы:

Похожие инструкции для Arria V

Бренды по названию

Популярные бренды

Intel Arria V, Руководство по дизайну

Результаты поиска

Содержание Arria V

Отзывы:

Похожие инструкции для Arria V

Бренды по названию

Популярные бренды