Intel 460GX Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 294

background image

Intel® 460GX Chipset Software Developer’s Manual

2-33

Register Descriptions

001 0111b Memory Read that was to be retried and received a HITM
001 1000b Memory Read with active OWN# and received a HITM
001 1001b Memory Read from a CPU that received a HITW
001 1010b Memory Read from a CPU that received a HITM
001 1011b Memory Read from PCI that received a HITW
001 1100b Memory Read from PCI that received a HITM
001 1101b Memory Write from PCI that received a HITM
010 0001b EV0 Events
010 0010b EV0 Clocks
010 0011b EV1 Events
010 0100b EV1 Clocks

7

reserved(0).

6:5

Disable Source
Selects event that will disable the performance monitor.

00b Never

Disable.

01b

Disable when this counter is overflowed (Note that if this setting is used, and bits
[4:3] are set to ’Enable Always’, then when this counter is overflowed, counting
will not resume until the counter is loaded with a non-overflow value).

10b

Disable on falling edge of SAC Event 0.

11b

Disable on falling edge of SAC Event 1.

4:3

Enable Source
Selects event that will enable the performance monitor.

00b Never

Enable.

01b

Enable Always (Disable events overrides this setting and will disable counting).

10b

Enable on rising edge of SAC Event 0.

11b

Enable on rising edge of SAC Event 1.

2:0

Reload Control
Selects event that will control the Reloading of the performance monitor with the value
written into the associated PMD2 register.

000b Never

Reload.

001b  Reload when counter overflows.
010b  Reload on SAC Event 0 Asserted.
011b  Reload on SAC Event 1 Asserted.
100b  Reload on SAC Event 0 Asserting edge.
101b  Reload on SAC Event 1 Asserting edge.

Note:

When counting retried reads (code of 110_0110b) the logic will count reads that were to be retried,
but got a HITM# and therefore the HITM# overrides the retry. For an exact count of reads that are
truly retried, count retried reads (110_0110b) and subtract out the number of reads that were to be
retried but got a HITM# (code of 001_0111b). This give the exact number of reads that were retried
on the bus.

«
...
51
52
53
54
55
...
»

Содержание 460GX







































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 460GX

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: N.A.T. Страницы: 32

Бренд: ZALMAN Страницы: 4

Бренд: Accom Страницы: 15

Бренд: Dolphin Страницы: 9

Бренд: Kanguru Страницы: 13

Бренд: Qlogic Страницы: 8

Бренд: ZALMAN Страницы: 5

RouterBOARD 411R

Бренд: 4gon Страницы: 2

EZ-Extender Analog 120-Pin Probing Board

Бренд: Analog Devices Страницы: 29

Seven Solutions WR-ZEN Series

Бренд: Orolia Страницы: 167

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

Бренд: Caen Страницы: 14

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

PXI PXITM -1000

Бренд: National Instruments Страницы: 55

Бренд: IEI Technology Страницы: 136

Бренд: Xilinx Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды