Intel 10 Gigabit AT Ethernet Server Adapter Скачать руководство пользователя страница 19

Страница: 19 / 165

Installing the Adapter

Select the Correct Slot

One open PCI-Express slot, x4, x8, or x16, depending on your adapter.

NOTE:

Some systems have physical x8 PCI Express slots that actually only support lower speeds.

Please check your system manual to identify the slot.

Insert the Adapter into the Computer

1. If your computer supports PCI Hot Plug, see your computer documentation for special installation

instructions.

2. Turn off and unplug your computer. Then remove the cover.

CAUTION:

Turn off and unplug the power before removing the computer's cover. Failure to

do so could endanger you and may damage the adapter or computer.

3. Remove the cover bracket from an available slot.

4. Insert the adapter, pushing it into the slot until the adapter is firmly seated. You can install a smaller

PCI Express adapter in a larger PCI Express slot.

CAUTION:

Some PCI Express adapters may have a short connector, making them

more fragile than PCI adapters. Excessive force could break the connector. Use cau-
tion when pressing the board in the slot.

5. Secure the adapter bracket with a screw, if required.

6. Replace the computer cover and plug in the power cord.

7. Power on the computer.

Connecting Network Cables

Connect the appropriate network cable, as described in the following sections.

Содержание 10 Gigabit AT Ethernet Server Adapter






































































































































































Результаты поиска

Содержание 10 Gigabit AT Ethernet Server Adapter

Отзывы:

Intel 10 Gigabit AT Ethernet Server Adapter, Руководство пользователя, Страница: 19 / 165

Результаты поиска

Содержание 10 Gigabit AT Ethernet Server Adapter

Отзывы: