Integra DTR-70.3, Инструкция по эксплуатации

Страница: 13 / 108

13
En
Speaker Configuration
The following table indicates the channels you should use
depending on the number of speakers that you have.
No matter how many speakers you use, 2 powered
subwoofers are recommended for a really powerful and
solid bass.
To get the best from your surround sound system, you
need to set the speaker settings automatically
(
➔
page 31 ) or manually (
➔
page 49 ).
*1 If you’re using only one surround back speaker, connect it to
the
SURR BACK/ZONE 3 L
terminals.
Attaching the Speaker Cable Labels
The speaker terminals are color-coded for identification
purpose.
The supplied speaker cable labels are also color-coded and
you should attach them to the positive (+) side of each
speaker cable in accordance with the table above. Then all
you need to do is to match the color of each label to the
corresponding speaker terminal.
Speaker Connection Precautions
Read the following before connecting your speakers:
• You can connect speakers with an impedance of between
4 and 16 ohms. If the impedance of any of the connected
speakers is 4 ohms or more, but less than 6 ohms, be sure
to set the minimum speaker impedance to “
4ohms ”
(
➔
page 49
). If you use speakers with a lower
impedance, and use the amplifier at high volume levels
for a long period of time, the built-in protection circuit
may be activated.
• Disconnect the power cord from the wall outlet before
making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive and negative wires.
Doing so may damage the AV receiver.
• Make sure the metal core of the wire does not have
contact with the AV receiver’s rear panel. Doing so may
damage the AV receiver.
• Don’t connect more than one cable to each speaker
terminal. Doing so may damage the AV receiver.
• Don’t connect one speaker to several terminals.
Number of
speakers 2 3 4 5 6 7 7 7 8 8 9 9 9 10 11
Front speakers
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Center
speaker
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Surround
speakers
✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Surround back
speaker
*1
✔ ✔ ✔ ✔
Surround back
speakers
✔ ✔ ✔ ✔
Front high
speakers
✔ ✔ ✔ ✔ ✔ ✔
Front wide
speakers
✔ ✔ ✔ ✔ ✔ ✔
Speaker Color
Front left, Front high left, Front wide left,
Zone 2 left White
Front right, Front high right, Front wide right,
Zone 2 right Red
Center Green
Surround left, Zone 4 left Blue
Surround right, Zone 4 right Gray
Surround back left, Zone 3 left Brown
Surround back right, Zone 3 right Tan