Integra DTR-70.3, Инструкция по эксплуатации

Страница: 60 / 108

60
En
■
Contrast
*1*3*5
`
–50 to 0 to +50
With this setting you can adjust contrast. “ –50 ” is the
least. “ +50 ” is the greatest.
■
Hue
*1*3*5
`
–50 to 0 to +50
With this setting you can adjust the red/green balance.
“
–50 ” is the strongest green. “ +50 ” is the strongest red.
■
Saturation
*1*3*5
`
–50 to 0 to +50
With this setting you can adjust saturation. “ –50 ” is the
weakest color. “ +50 ” is the strongest color.
■
Color Temperature
*3*5
`
Warm
`
Normal
`
Cool
With this setting you can adjust the color temperature.
■
Gamma
*3*5
`
–3 to 0 to +3
Adjust the balance of incoming picture R (red), G
(green), and B (blue) color data signal to the output
color data signal.
■
Red Brightness
*3*5
`
–50 to 0 to +50
With this setting you can adjust the picture red
brightness. “
–50 ” is the darkest. “ +50 ” is the
brightest.
■
Red Contrast
*3*5
`
–50 to 0 to +50
With this setting you can adjust red contrast. “ –50 ”
is the least. “ +50 ” is the greatest.
■
Green Brightness
*3*5
`
–50 to 0 to +50
With this setting you can adjust the picture green
brightness. “
–50 ” is the darkest. “ +50 ” is the
brightest.
■
Green Contrast
*3*5
`
–50 to 0 to +50
With this setting you can adjust green contrast.
“
–50 ” is the least. “ +50 ” is the greatest.
■
Blue Brightness
*3*5
`
–50 to 0 to +50
With this setting you can adjust the picture blue
brightness. “
–50 ” is the darkest. “ +50 ” is the
brightest.
■
Blue Contrast
*3*5
`
–50 to 0 to +50
With this setting you can adjust blue contrast. “ –50 ”
is the least. “ +50 ” is the greatest.
Note
• “ Picture Adjust ” cannot be used with the
NET
input selector.
*1 This procedure can also be performed on the remote controller
by using the Home menu (
➔
page 41
).
*2 When a 3D video source is input, “ Wide Mode ” is fixed to
“ Full ”.
*3 When the “ Picture Mode ” setting is set to anything other than
“ Custom ”, this setting cannot be used.
*4 If the “ Resolution ” setting is set to “ 4K Upscaling ”
(
➔
pages 46 , 59 ), this setting is fixed to “ Off ”.
*5 Press CLR if you want to reset to the default value.
*6 If you are using the analog RGB input, this setting is not
available.
*7 When the “ Noise Reduction ” setting is set to anything other
than “ Off ”, this setting cannot be selected.
*8 When “ Resolution ” is set to “ 1080/24 ” or “ 4K Upscaling ”
while “ Monitor Out ” is set to “ Analog ”, the video is output
in 1080i.
*9
When “ Resolution ” is set to “ 1080/24 ” or “ 4K Upscaling ”
while “ Monitor Out ” is set to “ HDMI Sub ” or “ Both(Sub) ”,
the video is output in 1080p.
*10 When “ Resolution ” is set to “ Auto ” while “ Monitor Out ” is
set to “ Analog ”, the video is output as “ Through ”.
Audio Selector
You can set priorities of audio output when there are both
digital and analog inputs.
■
Audio Selector
`
ARC :
The audio signal from your TV tuner can be sent to
the
HDMI OUT MAIN
of the AV receiver.
*1
With this selection, the TV’s audio can be
automatically selected as a priority among other
assignments.
`
HDMI :
This can be selected when HDMI IN has been
assigned as an input source. If both HDMI ( HDMI
IN ) and digital audio inputs ( COAXIAL IN or
OPTICAL IN ) have been assigned, HDMI input is
automatically selected as a priority.
`
COAXIAL :
This can be selected when COAXIAL IN has been
assigned as an input source. If both coaxial and
HDMI inputs have been assigned, coaxial input is
automatically selected as a priority.
`
OPTICAL :
This can be selected when OPTICAL IN has been
assigned as an input source. If both optical and
HDMI inputs have been assigned, optical input is
automatically selected as a priority.
`
Multich :
The AV receiver always outputs analog signals from
multichannel analog input.
`
Analog :
The AV receiver always outputs analog signals.