background image

102

En

Specifications (DTR-80.3)

Amplifier Section

Video Section

Tuner Section

General

HDMI

Video Inputs

Video Outputs

Rated Output Power
  All channels:

(North American)
145 watts minimum continuous power 
per channel, 8 ohm loads, 2 channels 
driven from 20 Hz to 20 kHz, with a 
maximum total harmonic distortion of 
0.05% (FTC)
175 watts minimum continuous power 
per channel, 8 ohm loads, 2 channels 
driven at 1 kHz, with a maximum total 
harmonic distortion of 0.7% (FTC)
185 watts minimum continuous power 
per channel, 6 ohm loads, 2 channels 
driven at 1 kHz, with a maximum total 
harmonic distortion of 0.1% (FTC)

(Others)

9 ch

 × 

220 W at 6 ohms, 1 kHz, 1 ch driven 

of 1 % (IEC)

Maximum Effective Output Power

(Others)

9 ch

 × 

280 W at 6 ohms, 1 kHz, 1 ch driven 

(JEITA)

Dynamic Power

*

*

 IEC60268-Short-term maximum output power

400 W (3 

Ω

, Front)

300 W (4 

Ω

, Front)

180 W (8 

Ω

, Front)

THD+N (Total Harmonic DisNoise)

0.05% (20 Hz - 20 kHz, half power)

Damping Factor

60 (Front, 1 kHz, 8 

Ω

)

Input Sensitivity and Impedance (Unbalance)

200 mV/47 k

Ω

 (LINE)

2.5 mV/47 k

Ω

 (PHONO MM)

Rated RCA Output Level and Impedance

1 V/470 

Ω

 (PRE OUT)

Maximum RCA Output Level and Impedance

5.5 V/470 

Ω

 (PRE OUT)

Phono Overload

70 mV (MM 1 kHz 0.5%)

Frequency Response

5 Hz - 100 kHz/+1 dB, -3 dB (Direct mode)

Tone Control Characteristics

±10 dB, 50 Hz (BASS)
±10 dB, 20 kHz (TREBLE)

Signal to Noise Ratio

110 dB (LINE, IHF-A)
80 dB (PHONO MM, IHF-A)

Speaker Impedance

4

Ω

 - 16 

Ω

Input Sensitivity/Output Level and Impedance

1 Vp-p/75 

Ω

 (Component and S-Video Y)

0.7 Vp-p/75 

Ω

 (Component P

B

/C

B

, P

R

/C

R

)

0.28 Vp-p/75 

Ω 

(S-Video C

)

1 Vp-p/75 

Ω 

(Composite

)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, -3 dB

FM Tuning Frequency Range

(North American)

87.5 MHz - 107.9 MHz

(Others)

 

87.5 MHz - 108.0 MHz, RDS

AM Tuning Frequency Range

522/530 kHz - 1611/1710 kHz

Preset Channel

40

Power Supply

(North American)

AC 120 V, 60 Hz

(Others)

AC 220 - 240 V, 50/60 Hz

Power Consumption

(North American) 

12.8 A

(Others) 

1160 W

No-sound Power Consumption

(North American)

135 W

(Others)

145 W

Stand-by Power Consumption

(North American)

0.2 W

(Others)

0.3 W

Dimensions (W × H × D)

435 mm × 198.5 mm × 455 mm
17-1/8" × 7-13/16" × 17-15/16"

Weight

24.0 kg (52.9 lbs.)

Input

IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7, 
AUX INPUT

Output

OUT MAIN, OUT SUB

Video Resolution

1080p

Audio Format

Dolby TrueHD, DTS-HD Master Audio, 
DVD-Audio, DSD

Supported

3D, Audio Return Channel (OUT MAIN), 
DeepColor, x.v.Color, LipSync, 
CEC (RIHD)

Component

IN 1, IN 2, IN 3

S-Video

BD/DVD, VCR/DVR, CBL/SAT, GAME

Composite

BD/DVD, VCR/DVR, CBL/SAT, GAME, 
AUX

Analog RGB

PC IN

Component

MONITOR OUT, ZONE2 OUT

S-Video

MONITOR OUT, VCR/DVR OUT

Composite

MONITOR OUT, VCR/DVR OUT, 
ZONE2 OUT

Содержание DTR-70.3













































































































Отзывы: