insys icom ISDN TA 4.0 Скачать руководство пользователя | Manualshive

Страница: 13 / 100

background image

INSYS ISDN TA 4.0

Safety

2.8

Safety Instructions for Electrical Installation

The electrical connection must only be made by authorised expert personnel ac-
cording to the wiring diagrams.
The notes to the electrical connection in the manual must be observed. Otherwise,
the protection category might be affected.
The safe disconnection of circuits, which are hazardous when touched, is only en-
sured if the connected devices meet the requirements of VDE T.101 (Basic re-
quirements for safe disconnection).
The supply lines are to be routed apart from circuits, which are hazardous when
touched, or isolated additionally for a safe disconnection.

2.9

General Safety Instructions

Caution!

Moisture and liquids from the environment may seep into
the interior of the product!

Fire hazard and damage of the product.

The product must not be used in wet or damp
environments, or in the direct vicinity of water. Install the
product at a dry location, protected from water spray.
Disconnect the power supply before you perform any work
on a device which may have been in contact with moisture.

Caution!

Short circuits and damage due to improper repairs and
modifications as well as opening of maintenance areas.

Fire hazard and damage of the product.

It is not permitted to open the product for repair or
modification.

Caution!

Overcurrent of the device supply!

Fire hazard and damage of the product due to overcurrent.

The product must be secured with a suitable fuse against
currents exceeding 1.6 A.

13

«
...
11
12
13
14
15
...
»

Содержание ISDN TA 4.0





































































































Отзывы:

Нет отзывов

Похожие инструкции для ISDN TA 4.0

Бренд: 3idee Страницы: 7

Бренд: 3idee Страницы: 7

Бренд: 3idee Страницы: 7

hp27-o VESA Adapter

Бренд: 3idee Страницы: 9

Бренд: U.S. Converters Страницы: 12

Freedom SW 2000

Бренд: Xantrex Страницы: 36

CrossPower C4L5200-ETH

Бренд: C4Line Страницы: 26

Бренд: Grandstream Networks Страницы: 75

Бренд: Konexx Страницы: 17

Бренд: Dantel Страницы: 48

Enercell 273-331

Бренд: Enercell Страницы: 1

Бренд: TRUlink Страницы: 36

XAV1501 - Powerline AV+ 200 Adapter

Бренд: NETGEAR Страницы: 2

Бренд: VARIZOOM Страницы: 2

Бренд: Macpower & Tytech Страницы: 26

CardPark APA-4510

Бренд: Adaptec Страницы: 8

U244-001-HDMI-R

Бренд: Tripp Lite Страницы: 12

Бренд: HP Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды