manualshive.com logo in svg

insys icom ISDN TA 4.0, Руководство пользователя

Поделиться
Скачать
insys icom ISDN TA 4.0 Скачать руководство пользователя страница 32

Operating Principle 

INSYS ISDN TA 4.0 

 

8

 

Operating Principle 

This chapter describes the basic procedures to operate and configure an 

 

INSYS 

ISDN TA 4.0. In addition, you get an overview about the operating elements of the 
HSComm software. 

There are to methods to operate and configure the INSYS ISDN TA 4.0. In general, 
the INSYS ISDN TA 4.0 is configured and operated via AT commands. An own 
command set is used for special ISDN parameters. A TA+Configurator with special 
command set is used for remote configuration. You can enter the different 
command sets using a terminal program. Alternatively, you can configure the most 
important functions comfortably using the configuration software HSComm.  

8.1

 

Operation with the Terminal Program 

In general, any terminal program can be used. We recommend the program 
Teraterm from T.Teranishi. It is available free of cost on the Internet at 
http://hp.vector.co.jp/authors/VA002416/teraterm.html. 

 

Configuring and operating the INSYS ISDN TA 4.0 with a terminal program 

 

How to configure and operate the INSYS ISDN TA 4.0 with a terminal 

program. 

 

The INSYS ISDN TA 4.0 is connected to the PC and switched on. 

 

A terminal program is installed on the PC. 

1.

 

Start your terminal program. 

2.

 

Select the serial port, to which your INSYS ISDN TA 4.0 is connected. 

 

COM1 under Windows corresponds to /dev/ttyS0 under Linux. 

3.

 

Type the character string 

AT

 into the terminal program. Complete the 

entry by pressing the Enter key. 

 

Each command input starts with 

AT

 and is completed with the Enter 

key. 

 

The 

OK

. 

INSYS ISDN TA 4.0 replies with 

 TA 4.0 does not respond, this may have two 

 TA 4.0 is connected to another serial port. Check it 

and repeat step 3. 

Configure the INSYS ISDN TA 4.0 using AT commands. 

 

If the INSYS ISDN
probable reasons: 
a) the INSYS ISDN TA 4.0 is switched off or 
b) the INSYS ISDN

4.

 

32 

 

Содержание ISDN TA 4.0





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды