manualshive.com logo in svg

INNO VIEW 5 Pro, Руководство пользователя

Поделиться
Скачать
INNO VIEW 5 Pro Скачать руководство пользователя страница 8

8

VIEW 5 Pro

Transport and Storage Precautions

①  When the splicer is moved from cold to warm environment, you should allow the splicer to warm up gradually. 
      Otherwise, the condensation generated inside will bring harmful effects to the splicer.
②  Pack the fusion splicer well for long time storage.
③  Keep the splicer clean and dry.
④  The splicer is precision adjusted and aligned. Always keep the splicer in its carrying case to protect from damage and  
      dirt. Put cushion package outside the carrying case for long distance transportation.
⑤  Always avoid leaving the splicer in direct sunlight or expose to excessive heat.
⑥  DO NOT store the splicer in dusty or environment. This may result in electric shock, splicer malfunction or poor  
      splicing performance.
⑦  Keep the humidity to a minimum level where the splicer is stored. The humidity must not exceed 95%.

2.2 Installation

⚠ Important!

Follow these instructions carefully.

Unpacking the Splicer

Hold the handle upwards, and then lift the splicer out of the carrying case. As shown below.

Содержание VIEW 5 Pro






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды