18 IDS1200 INSTALLER MANUAL - NO. 700-171-02B ISSUED AUGUST 2002 VER 1.18
IDS1200 INSTALLER MANUAL
If the
AC
power should fail, the panel will wait for this period of time before reporting the mains failure to the
base station or logging the event to the event log. If the
AC
power is restored after the time out period has
ended the same time out period will apply before the restoral event is reported and logged.
If the
AC
power is restored during the delay period neither the power failure nor the power restoral will be
reported or logged to the event log. This delay eliminates unnecessary reporting if the
AC
power to the panel
is accidentally removed for a short period (provided the back up battery is in good condition, short
AC
power
failures will not affect the functioning of the alarm system).
Select the appropriate value from the table on the previous page.
6
2
N
O
I
T
A
C
O
L
D
I
d
a
p
y
e
K
1
t
i
g
i
D
2
t
i
g
i
D
e
u
l
a
V
n
o
i
t
c
A
e
u
l
a
V
n
o
i
t
c
A
0
d
e
l
b
a
s
i
d
n
o
it
it
r
a
p
e
t
a
n
r
e
tl
a
f
o
g
n
i
m
r
A
1
1
n
o
it
it
r
a
p
o
t
d
e
n
g
i
s
s
a
d
a
p
y
e
K
1
d
a
p
y
e
K
r
e
t
s
a
M
.
e
.i
d
e
l
b
a
n
e
n
o
it
it
r
a
p
e
t
a
n
r
e
tl
a
f
o
g
n
i
m
r
A
2
2
n
o
it
it
r
a
p
o
t
d
e
n
g
i
s
s
a
d
a
p
y
e
K
NB: Before entering this information ensure that the number of partitions (location 857)
has been set up.
If a keypad is assigned to a partition that does not exist the panel will shut the keypad out and the keypad
ID will have to be defaulted by holding down the
[1]
and the
[
!!!!!
]
keys when the panel is powered up. The
keypad will then be defaulted to partition 1.
The keypad ID is a two digit number which is used by the keypad and must be entered individually at each
keypad. If the first digit is a “1” then the keypad is a master keypad that can alter the status of either
partition. If the first digit is a “0” then the keypad can only affect the partition to which it is assigned.
The second digit determines to which partition the keypad is assigned.
EXAMPLE
:
To assign master status to a keypad in partition 2, enter
[12]
into location 26 of the appropriate keypad
(1=Master, 2=Partition 2).
To assign ordinary status to a keypad in partition 1, enter
[01]
into location 26 of the appropriate keypad
(0=Ordinary, 1=Partition 1).
7
2
N
O
I
T
A
C
O
L
t
u
O
e
m
i
T
d
a
p
y
e
K
r
e
t
s
a
M
e
u
l
a
V
n
o
i
t
c
A
0
n
o
it
it
r
a
p
d
e
t
c
e
l
e
s
n
i
s
y
a
t
S
)
tl
u
a
f
e
D
(
1
n
o
it
it
r
a
p
l
a
n
i
g
ir
o
o
t
s
t
r
e
v
e
R
This option affects how a master keypad is assigned to a specific partition. If the
[
MODE
]
key is held down
and a partition number pressed, the keypad will be assigned to the selected partition. If this option is
enabled (a value of
[0]
is programmed), the keypad will remain assigned to the selected partition, otherwise
the keypad will revert to its original partition 20 seconds after the last key is pressed.
9
2
-
8
2
S
N
O
I
T
A
C
O
L
d
e
v
r
e
s
e
R
