Ingersoll-Rand P185AWIR Скачать руководство пользователя страница 73

Страница: 73 / 92

4IRI8N - 4IRI8T ENGINE

Operating & Maintenance Manual

Engine Identification

Serial Number Location

The engine serial number is stamped on engine name plate on top of rocker cover. See
illustration on Table 1.

Confirmation of Engine Number

It is advisable to quote the engine serial number together with the machine serial number, as
it is required when you contact the Ingersoll-Rand branch or distributor for repair, service or
parts ordering.

INGERSOLL-RAND ENGINE AFTER SERVICE

Contact your Ingersoll-Rand dealer for periodical inspection and maintenance.

Ingersoll-Rand parts are identical with those used in the engine production, and accordingly,
they are warranted by Ingersoll-Rand.

Genuine Ingersoll-Rand parts are supplied by your Ingersoll-Rand branch or distributor.

Please ensure that only genuine Ingersoll-Rand parts, lubricants and fluids are used for
service and/or repair.

WARNING

Conduct confirmation of engine serial number with the engine stopped. To avoid being
injured, do not check it while the engine is still hot.

Содержание P185AWIR





























































































Результаты поиска

Содержание P185AWIR

Отзывы:

Похожие инструкции для P185AWIR

Бренды по названию

Популярные бренды

Ingersoll-Rand P185AWIR, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185AWIR

Отзывы:

Похожие инструкции для P185AWIR

Бренды по названию

Популярные бренды