Ingersoll-Rand P185AWIR Скачать руководство пользователя страница 46

Страница: 46 / 92

Operating & Maintenance Manual

SECTION 5 - OPERATION

CONTROL PANEL - Diagnostics/Auto
Shutdown (Standard and Optional)

Instruments & Controls (STANDARD)

Compressor Discharge Pressure
Gauge -

Indicates pressure in

receiver tank, psi (kPa).

Hourmeter -

Records running time

for maintenance.

Power Switch -

Rotate “ON” to

activate system prior to starting.
Rotate “OFF” to stop engine.

Instruments & Controls (OPTIONAL)

High Engine Temperature -

Coolant

above 220°F (104°C).

Low Engine Oil Pressure

- 12 psi or

less.

High Compressor Temperature -

248°F (120°C)

Air Filters Restricted

- Needs

servicing.

Spare

10.

Alternator Not Charging

- Needs

attention.

11.

Low Fuel Level

- Must add fuel to

operate.

12.

Fuel Level Gauge

- Indicates

amount of fuel in tank.

13.

Engine Speed Gauge

- Indicates

engine speed.

14.

Discharge Air Temp. Gauge

Indicates in °F (82°C) to 210°F
(99°C).

15.

Engine Oil Pressure Gauge -

Indicates engine oil pressure.

16.

Engine Water Temp. Gauge

Indicates coolant temperature, with
normal operating range from 180°F
(82°C) to 210°F (99°C).

17.

Voltmeter

- Indicates battery

condition.

18.

Ether Inject Button

- Injects a

measured shot. USE SPARINGLY.

19.

Service Air Button

- After warm-up,

PUSH. Provides full air pressure at
the service outlet. Indicates engine
speed.

20.

Spare

21.

Spare

Содержание P185AWIR





























































































Результаты поиска

Содержание P185AWIR

Отзывы:

Похожие инструкции для P185AWIR

Бренды по названию

Популярные бренды

Ingersoll-Rand P185AWIR, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание P185AWIR

Отзывы:

Похожие инструкции для P185AWIR

Бренды по названию

Популярные бренды