Ingersoll-Rand LA1500R, Инструкция по установке и эксплуатации

Страница: 4 / 123

4 SAM0068 - Edition 4
ENGLIS
H
DESCRIPTION
Liftstar Series winches are air powered, planetary geared units designed
for lifting and pulling applications . The winch utilizes a spring applied
disc brake which is automatically engaged when the throttle is in the
neutral position or if there is a lack of air pressure. The output from the
externally mounted air gear motor is transmitted through a coupling and
shaft to the planetary reduction gear assembly. The planetary reduction
gear drives a ring gear which is connected to the wire rope drum through
the output shaft.
Pullstar Series winches are air powered, planetary geared units provided
with a disengaging clutch and are designed for pulling applications only .
The winch utilizes a spring applied disc brake which is automatically
engaged when the throttle is in the neutral position or if there is a lack of
air pressure. The output from the externally mounted air gear motor is
transmitted through a coupling and shaft to the planetary reduction gear
assembly. The planetary reduction gear drives a ring gear which is
connected to the wire rope drum through the output shaft.
INSTALLATION
Prior to installing the winch, carefully inspect it for possible shipping
damage.
Winches are supplied fully lubricated from the factory.
Check oil levels and adjust as necessary before operating winch. Refer to
“LUBRICATION” section for recommended oils.
• Owners and users are advised to examine specific, local or other
regulations which may apply to a particular type of use of this
product before installing or putting winch to use.
Mounting
Mount the winch so the axis of the drum is horizontal and the motor vent
cap is no more than 15° off top vertical center. If the winch is to be
mounted in an inverted position or if the winch axis will be tilted more
than 10° from horizontal, contact your distributor or the nearest service
repair center for additional installation information.
1.
The winch mounting surface must be flat and of sufficient strength
to handle the rated load plus the weight of the winch and attached
equipment. An inadequate foundation may cause distortion or
twisting of the winch end covers and spacers resulting in winch
damage.
2. Make sure the mounting surface is flat to within 0,127 mm (0,005
inch) per inch of drum length. Shim if necessary.
3. Mounting bolts must be Grade 8 or better. Use self-locking nuts or
nuts with lockwashers.
4. Refer to Table 1 and Dwg. MHP2631 for winch mounting
dimensions and mounting bolt hole sizes.
5. Maintain a fleet angle between the sheave and winch of no more
than 1-1/2 degrees. The lead sheave must be on a center line with the
drum and, for every 25 mm of drum length, be a least 0,5 metre from
the drum.
6. Do not weld to any part of the winch.
(Dwg. MHP2631)
Model No
Sound
Pressure
Level
Sound
Power
Level
Winch
Nominal
Overload
Setting
(last layer)
Drum
Barrel
Diameter
Minimum
Air Hose
Size
Drum
Flange
Diameter
Motor
Port Inlet
Size
Maximum
Foundation
Anchor
Shear Force
at One
Capscrew*
dBA dBA kg mm inches mm inches N
LS150R
89 103
180
140 1/2 231 1/2 BSP
1440
LS300R 360 2880
LS600R
720 5760
LS600RGC 86 99
LA1500R 88 102
1800 108 3/4 290 3/4 BSP 17890
LS1500RGC 85 99
LS2000R
95 111 2400
244
1-1/4
442
1-1/4BSP
20620
LS2000RGC 273
LS5000R
87 102 6000 368 670 31530
LS5000RGC
PS1000R 83 103
---
140 1/4 231 1/2 BSP 8390
PS1000RGC 86 99
PS2400R 88 102
180 3/4 290 3/4 BSP 25740
PS2400RGC 85 99
PS4000R
95 111
244
1-1/4
442
1-1/4 BSP
35120
PS4000RGC 273
PS10000R
87 102 368 670 51950
PS10000RGC
Notes:
1. Sound measurements have been made in accordance with ISO 11201, ISO 3744-3746 and ISO 4871 test specifications for sound from pneumatic
equipment. Readings shown are based on the average noise level of each winch configuration, proportionate to the utilized time in a regular cycle.
2. Lpc (Peak Sound Pressure) does not exceed 130 dB.
3. Performance based on 6,3 bar operating pressure.
4. Maximum Foundation Anchor Shear Force at One Capscrew, value based on use of recommended fastener grade and size.
“A”
“B”
Drum
“D”
Note:
1
“C”