5
Password
Protection
Available
Network Port
One RJ45 10/100M self-adaptive Ethernet port
Applicable
Protocols
IPv4, IPv6, TCP, UDP, IGMP, DHCP, FTP, SNMP (V3),
SMTP, NTP, RTP, RTSP, RTCP, HTTP, HTTPS, TSL, SSL,
802.1X, QoS, PPPoE, DNS, ARP, ICMP, UPNP, DDNS,
Profile S
Alarm
2 alarm inputs, 1 relay output
Power Supply
PoE
（
IEEE 802.3af Class 2
）
/12VDC
（
10VDC~40VDC
）
/24VAC
（
12VAC~40VAC
）
Power
Consumption
＜
5W (when the camera is focusing, the power
consumption will be less than 8W.)
ESD protection
±
6KV(all ports)
Surge protection
±
6KV
（
network port
）
Operating
Temperature
14°F~122°F (-10°C~+50°C)
Storage
Temperature
-4°F~140°F (-20°C~+60°C)
Operating
Humidity
0%-90% RH (non-condensing)
Dimensions
(H×W×L)
2.84"×2.97"×5.47" (72mm×75.5mm×139mm)
Box Dimensions
(L×W×H)
8.07"×4.92"×3.94" (205mm×125mm×100mm)
Unit Weight
1.21lbs. (0.55kg)
Shipping Weight
1.54lbs. (0.70kg)
1.6 Notice
1.
Firstly perform network settings after login. The gateway IP address should
be set as that of the connected to the network camera.
6
2.
The IP address is not allowed to conflict with that of other devices; otherwise,
you cannot visit the camera.
3.
If the purchased IP camera utilizes PoE power supply, please connect
equipments according to the parameter of the Power Supply Switcher strictly.
Furthermore, practical test of maximum network cable length for the Power
Supply Switcher must be performed, so as to avoid the camera failure caused
by insufficient power supply of the Power Supply Switcher, or to avoid the
destruction of Switcher.
7
CHAPTER II INSTALLATION AND PORT INTRODUCTION
2.1 Installation Precautions
Do not drop the camera or subject it to strong knock.
Do not point the camera lens toward the sun or other strong light.
Do not install the camera in environment with temperature beyond the
acceptable range (from -10°C to 50°C), or with high humidity, direct
rainfall, frequent vibrations and shocks.
Add with auxiliary illumination device in case of low illumination to avoid
poor image quality.
2.2 Back Panel and Control Parts
Figure 2-1 Back View
①
Alarm Input/Output, Audio Input/Output, RS-485 Terminal
②
Network Port (used for PoE power supply)
8
③
Analog Video Output
④
TF Card Slot
⑤
Network LED Indicator
⑥
Back Focus Adjusting
⑦
Reset
⑧
Status LED Indicator
⑨
Arrester ground terminal
⑩
Power Input Terminal
Notes:
The analog video is closed when the MJPEG video stream is enabled.
To enable the analog video, please close the MJPEG video stream.
On the left of camera body (face the lens to view), there is an IRIS connector.
The pin definition is as follows:
Note:
The camera supports
DC DRIVE
. The default setting is DC DRIVE.
1
2
3
4
Figure 2-2
⑦
Reset button: The camera supports short press and extended press reset
modes. If press and hold the button from 2s to 15s (i.e. short press), Power
LED Indicator will turn green, and camera’s parameters will restore the
default values. If press and hold the button more than 15s (i.e. extended
press), Power LED Indicator will turn orange, and camera’s system will
resume factory default settings. Power LED Indicator will flicker quickly
while holding time is about 15s. Note: if press “Reset” button, the IP address
will become to 192.168.1.100.
⑥
Back Focus Adjusting button: Mount lens to the camera and install the
unit to the desirable place, then power on. Next, modulate the knobs on the
Pin
DC DRIVE
1
DAMP-
2
DAMP+
3
DRIVE+
4
DRIVE-
