Inficon UL5000 Скачать руководство пользователя страница 64

Страница: 64 / 108

Description of the Menu

iina

e 0

chn

ica

l ha

boo

6.6.4

Interfaces

•

Main Menu

Settings

Interfaces

The parameters of the interface can be set.

6.6.4.1

Control Location

•

Softkey 3:

Please refer to Chapter

6.6.4.1

Softkey 4:

RS232 Protocol

Please refer to Chapter

6.6.4.3

Softkey 7:

Recorder output

Please refer to Chapter

6.6.4.2

Softkey 8:

Scaling Recorder Output

Please refer to Chapter

6.6.4.4

Softkey 2:

PLC

The UL5000 is controlled via the Digital In connector (See Chapter

6.6.4.2

The START, STOP and ZERO buttons at the control panel are locked.

Softkey 3:

RS232

The UL5000 is controlled via RS232 interface by an external computer. In
this mode the UL5000 can not be controlled via keyboard. The START,
STOP and ZERO button at the machine are deactivated.

Softkey 5:

Local & PLC

The UL5000 is controlled via the Digital In connector or the START, STOP
and ZERO buttons at the control panel.

Softkey 6:

Local & RS232

The UL5000 is controlled via the Digital In connector or the START, STOP
and ZERO buttons at the control panel.

Softkey 7:

Local

The UL5000 is controlled via the START, STOP and ZERO buttons at the
control panel. The Digital In connector is not used.

Содержание UL5000













































































































Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды

Inficon UL5000, Техническое руководство

Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды