Inficon UL5000 Скачать руководство пользователя страница 84

Страница: 84 / 108

Error And Warning Messages

iina

e 0

chn

ica

l ha

boo

E34

24V voltage at MSV board is
too low!

Signal MVPZN on the MSV board is active. 24 V signal voltage is too low,
U < 18.3 V.

•

Fuse F1 on the MSV board has blown.

•

24 V power supply voltage is missing.

Switch off the UL5000!

The missing voltage will cause the exhaust valve on the scroll pump to
close which in turn can lead to a contamination of the vacuum system.

•

Reference voltage UREF on the MSV board XT7/1 is too high, U > 5 V.

E35

Anode-cathode voltage is too
high!

•

MSV board is faulty.

•

Anode-cathode voltage is higher than 130 V.

E36

Anode-cathode voltage is too
low.

•

MSV board is faulty.

•

Anode-cathode voltage is lower than 30 V.

E37

Suppressor voltage reference
value too high!

Signal MFSZH on MSV board is active. Suppressor signal command
variable is too high.

•

Suppressor voltage has a short circuit.

•

MSV is faulty.

E38

Suppressor potential too
high!

Suppressor potential is higher than 363V.

•

MSV board is faulty.

E39

Suppressor potential is too
low

Suppressor potential is lower than 297V.

•

MSV board is faulty.

E40

The anode potential exceeds
its nominal value by over
10%!

The actual anode potential exceeds its nominal value by 10%. The
nominal value can be displayed in the service menu.

•

MSV is faulty.

E41

The anode potential has
dropped below its nominal
value by over 10%!

The actual anode potential has dropped below its nominal value by 10%.
The nominal value can be displayed in the service menu.

•

Air inrush.

•

MSV is faulty.

E42

Nominal value of the anode
potential is too high!

Signal MFAZH on MSV board is active.

•

Anode voltage has been short circuited.

•

Nominal value of the anode voltage is too high. Anode voltage is limited
to about 1,200 V.

E43

Cathode current is too high!

•

Signal MPKZH on MSV board is active. Cathode current is too high, I
> 3.6 A.

•

MSV is faulty.

E44

Cathode current is too low!

•

Signal MPKZN on MSV board is active. Cathode current is too low, I >
0.2 A.

•

MSV is faulty.

W45 Emission for cathode 1 can

not be switched on!

Signal MSIBE on MSV board is not active. Emission for cathode 1 can not
be switched on. UL5000 switches to cathode 2. Please order a new ion
source.

W46 Emission for cathode 2 can

can not be switched

Signal MSIBE on MSV board is not active. Emission for cathode 2 can not
be switched on. UL5000 switches to cathode 1. Order a new ion source.

No.

Displayed Message

Description and possible solutions

Содержание UL5000













































































































Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды

Inficon UL5000, Техническое руководство

Результаты поиска

Содержание UL5000

Отзывы:

Похожие инструкции для UL5000

Бренды по названию

Популярные бренды