Inficon Sensistor Sentrac Скачать руководство пользователя страница 47

Страница: 47 / 76

INFICON

Service Instructions | 5

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

47 / 76

Remove the Speaker (D).

Assemble

Check the speaker gasket. Replace with new if necessary.

Place the new Speaker correctly.

Reinstall the four screws (C) holding the Speaker.

Place the Front Panel correctly. Make sure that no cables are pinched between

the Front Panel and the chassis.

Reinstall and tighten the four screws (A) holding the Front Panel. Do not use

thread locking compound.

Connect all cables between the Front Panel and the PCB. Pay special attention

to J2. Do not use force!

Perform a function test before the assembly continues.

Ensure the following functions, check that the:

Blue LED is lit.

Display is lit up and is functions.

Touch function on the display is working.

Sound in earphone and speaker is working correctly.

Probe is working in both front and rear Probe sockets.

Electrical grounding is OK. Measure with a DVM between front probe

connection ground (the shield) and one of the screws in the back. The

resistance should be 9 ohm or lower.

If any of the above tests fails, see Troubleshooting [

}

21].

Reinstall the cover, see Assemble in Remove the Cover [

}

28].

Содержание Sensistor Sentrac













































































Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды

Inficon Sensistor Sentrac, Инструкция по эксплуатации

Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды