Inficon Sensistor Sentrac Скачать руководство пользователя страница 53

Страница: 53 / 76

INFICON

Service Instructions | 5

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

53 / 76

Remove the Probe PCB (A).

Remove the Probe Display Glass (C) and Display Glass Adhesive.

Remove any residual adhesive from the Probe handle upper part.

Assemble

Apply the new Display Glass Adhesive (D) on to the Display glass adhesive

alignment tool.

Remove the protective paper from the Display Glass Adhesive.

Firmly apply the new Display Glass Adhesive (D) into the Display Glass socket

and press.

Remove the protective paper from the Display Glass Adhesive.

Install the new Probe Display Glass (C). Make sure that the new Display Glass

is clean and free from dirt.

Remove the edge of protective paper from the OLED-display seal (E), leave the

protective paper in the center for now.

Firmly apply the OLED-display seal (E) on the Probe Display Glass (C).

Use a scalpel and gently remove the center piece in the OLED-display seal.

Reinstall the Probe PCB (A). See Assemble in Changing Probe PCB with

Display [

}

51].

Содержание Sensistor Sentrac













































































Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды

Inficon Sensistor Sentrac, Инструкция по эксплуатации

Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды