Inficon Sensistor Sentrac Скачать руководство пользователя страница 28

Страница: 28 / 76

5 | Service Instructions

INFICON

28 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

5.2 Remove the Cover

Part

Part no.

Qty

Consumables

Instrument casing

598-194

Disassemble

Disconnect the mains connector.

Use a Spanner for notched nut to remove the Probe Connection Port nut (A).

Remove the two screws (B) holding the cover (C).

Remove the cover (C).

Assemble

Reinstall the cover (C).

Make sure that the lock washer on the Probe Connection Port (LEMO connector

on main PCB) is still present. Important for proper grounding.

Make sure that no cables are pinched between the cover and the chassis.

Reinstall and tighten the two screws (B) holding the cover (C). Tighten to 4 Nm.

Reinstall the Probe Connection Port nut (A).

Use a Spanner for notched nut and tighten the Probe Connection Port nut.

Check the resistance between the ground pin in the mains socket and the

outside of the probe cable connector, should be 9 ohm or lower. If not, check

the lock washer on the Probe Connection Port.

Содержание Sensistor Sentrac













































































Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды

Inficon Sensistor Sentrac, Инструкция по эксплуатации

Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды