Inficon Sensistor Sentrac Скачать руководство пользователя страница 22

Страница: 22 / 76

4 | Troubleshooting

INFICON

22 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

4.2 Hardware Error Messages

Message

Indicators

Technical

Description

Cause of Warning

Measure

Error Code

Probe not

connected.

Blue LED

flashing.

communication

established

between probe

and instrument.

No probe or wrong

probe version

connected at start

up.

Make sure that the

probe has the

correct version and

connect the probe.

(None)

SD-card not

inserted.

Orange window

present on

screen.

Software can not

find the SD-card.

SD-card not

inserted.

Insert SD-card.

(None)

Battery

discharged.

Recharge

battery

Orange window

present on

screen. Blue LED

flashing at high

frequency.

No power.

Battery

discharged.

Recharge the

battery.

(None)

Reject level too

low for sensor

sensitivity.

Orange measure

window present

on screen.

Calibration

approved but

Reject level too

low for sensor

sensitivity.

Sensor sensitivity

too low to detect

leak in Reject level

size.

Change Reject

level value or

change to sensor

with higher

sensitivity.

(None)

Sensor signal

error, voltage

too high.

Change/

connect sensor

or change

probe.

Red measure

window present

on screen. Blue

LED flashing.

Sensor signal

baseline voltage

level too high,

above 3650 mV.

No connected

sensor or sensor

with Sens wire

broke (Pin 2).

Change sensor

and/or probe. If a

Combox used,

change the cable

between the

Combox and the

probe.

Sensor signal

error, voltage

too low.

Change sensor

or probe.

Red measure

window present

on screen. Blue

LED flashing.

Sensor signal

baseline voltage

level too low,

below 300 mV.

Broken sensor or

broken probe.

Change sensor or

probe.

Содержание Sensistor Sentrac













































































Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды

Inficon Sensistor Sentrac, Инструкция по эксплуатации

Результаты поиска

Содержание Sensistor Sentrac

Отзывы:

Похожие инструкции для Sensistor Sentrac

Бренды по названию

Популярные бренды