Inficon Contura S400 Скачать руководство пользователя страница 25

Страница: 25 / 68

INFICON

Operation | 6

Contura® S400-Operating-instructions-jina91en1-09-(2001)

25 / 68

6.2.6.1 Determine the Measuring mode

Using the pre-set Measuring mode "Universal" you can measure packaging of

different sizes and strengths.

Undesired measurement results in the Measuring mode "Universal" are

possible

Seriously damaged packaging (gross leaks) could be shown as "Leak-proof" in

testing, because when evacuating the measuring chamber, the filling gas is

completely sucked out of the packaging.

► In order to detect larger leaks, select another measuring mode for your product from

the table below. In this way the gross leak detection will also take into consideration

the packaging.

Measuring Mode /

Packaging Size

For example

Gross leak

detection

Testing several packages

Universal

Packages of

different sizes and

strengths

All types of gas filled

packages

Deactivated

Possible

Small & Soft

Less than 500 ml

Possible. The inaccuracy of the

measurement results increases with the

number of the packages. The

measurement result is dependent on

constant volume packaging. Total volume

< 500 ml. Only same number of packaging

per measurement cycle.

Sausage packaging,

individually wrapped salami

sausage

By outer

volume

Large & Soft

Greater than 500 ml

By evaluating

the leak rate

Possible. Only same number of packaging

per measurement cycle.

Chips bag

Small & Rigid

Recommended up

to 500 ml

Possible. Only same number of packaging

per measurement cycle. Depending on the

inner volume even with large numbers.

Coffee capsules, and soft

packaging with individual

products and sufficient

cavity (nuts)

By gas filled

inner volume

Содержание Contura S400





































































Результаты поиска

Содержание Contura S400

Отзывы:

Похожие инструкции для Contura S400

Бренды по названию

Популярные бренды

Inficon Contura S400, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание Contura S400

Отзывы:

Похожие инструкции для Contura S400

Бренды по названию

Популярные бренды