manualshive.com logo in svg

Incon TS-5000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Incon TS-5000 Скачать руководство пользователя страница 25

22

Enabling/Disabling SCM

After learning the channel(s), each channel will need to be enabled to allow containments to be monitored. The 

Containment Status reflects the current status of the channel.

Enabling SCM Channels

At the T5 FMS console (LCD or TSA), navigate to the SCM Control screen. Press the 

Enable/Disable

 button to enable 

the channel.
Only while the channel is enabled will that channel continuously monitor and test vacuum levels by activating the STP 

as necessary. Normal SCM operating vacuum level is between 2" Hg and 5" Hg. During vacuum recharge periods, it is 

normal for the vacuum levels to reach 6" Hg.

Note

:  A channel will not enable properly if it is not learned, in an alarm status, or if an error condition exists (such as a 

sensor malfunction). An alarm must be reset to enable a SCM channel.

Disabling SCM Channels

At the T5 FMS console (LCD or TSA), navigate to the SCM Control screen. Press the 

Enable/Disable

 button to disable 

the channel.

Important:  While the channel is 

Disabled

, SCM will neither maintain nor test containment vacuum levels.

Disabling the channel will force the console to display a Containment Not Enabled warning. This warning will also appear 

on the SCM History Report. The channel may be re-Enabled  at any time.
If alarms or errors occur, please refer to the Alarms chapter of this guide.

Содержание TS-5000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды