IMG BRASIL BIMG METVISA FTE.150 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

IMG BRASIL BIMG METVISA FTE.150 Скачать руководство пользователя страница 18

18

To deactivate the cyclic steam function, press the key .

The controller has a system that checks for possible faults in the temperature sensor. This fault

can be seen on the display.

Check the description of the failure:

Display

Descrição

Some corrupted configuration parameters were detected and for safety all of
them were restored to their factory value. The user must turn the controller off
and on to return to operation.

The controller detected a failure in the temperature sensor. Verify that the
sensor is properly connected to the controller and that the sensor is not
damaged.

The controller has detected that the temperature measured by the PTC sensor
is above normal operating conditions. Check that the sensor is properly
connected to the controller and that it is not broken or damaged.

4.3 Operating Procedures

Before operating the equipment, make the perfect cleaning, especially inside the oven.

Clean the equipment with the oven at room temperature and disconnected from the mains. Follow the
cleaning instructions in item 5 of this manual (below).

ATTENTION!

For the first use of  model equipment FTE.150 and FTE.300 (models with  carbon  steel  chamber
with high temperature paint finish) it is necessary to cure the paint inside the oven (chamber).
To  do  this,  the  empty  oven  must  be  switched  on  and  the temperature  raised  to  220°  C  for  a
minimum  of  60  minutes.  Follow  the  operating instructions in the following operation item.

During the curing process of the paint, odor and smoke will be released due to the burning of the
paint.

Turn off the machine and wait until the oven is at room temperature. After that your equipment
will be available for use.

•

Operation:

The equipment can only be operated after checking the correct arrangement of the

equipment, instructed in item 3.1, and after following the precautions and recommendations of the hydraulic
installation, electrical connection and gas installation, according to the instructions in items 3.2, 3.3 and 3.4.

Check the following operating instructions:

1. If you have installed a water valve, make sure it is open;

2. Turn the power switch to "1" (on) and wait until the temperature display show the set temperature;

«
...
16
17
18
19
20
...
»

Содержание BIMG METVISA FTE.150









































Отзывы:

Нет отзывов