28/11/02-\\SERVER\TECNICO\-SNZ\0Sit\hVtf500shie.doc-Scheda Identificazione Codice Padre (mac.sott.etc...)-
16 di 62 pagine.
Pagina
n°-
16
63MY
9 - SYSTEM SWITCHING ON
When you switch the system on, the keyboard displays the loading of the set up data
from the permanent memory "Eeprom" and the release software code. Then, for
about 2 seconds, it displays the identification machine code number .
For going on it is necessary to push the button “Close the vice”- pos. 19 / dr. RIOO55 - that activates
the oil pump - in the hydraulic models -
Please note that in some previous models the starting could be activated by pushing any other button.
If you push other buttons the display shows the error message: ER0034.
If you do not push any other button in 10 minutes, the electronic control deactivates the motor of the
oil unit (if the machine is hydralic). For starting up the system push again the button “Close the vice”
- the display shows for an instant a series of led lights-.
After this operation the system is ready to work.
The led lights on the function keys show the operative condition of the
machine . A series of led lights give information regarding the piece counter, hours counter and so on.
Sometimes after switching the machine on or after caused anomalies, the keyboard
display error codes ( for ex.the band is not tensioned during the transit ).Please refer to the enclosed error
codes list. Push any key to cancel such errors after eliminating the anomaly.
9.1 - KEYBOARD = Buttons description and use, see drawing RI0055.
Pushing the buttons FEED-BACK made with polyester support and IP65 protection,
you schedule any machine operation, including the position of cutting unit :
BACKWARD (16) push it to move the cutting unit away from the workpiece till the maximum programmed
point.The corresponding led light shows that the tool is moving.
FORWARD (17) push it to move the tool away from the workpiece till the minimum programmed point . The
corresponding led light shows that the tool is moving.
CUT START SETTING (14) The led light usually shows the cutting unit position as regards to the stroke
limits ( light flashing =in limit; led light unflashing = out of limit ).
CUT END SETTING (15) as for the key 14 , the led light usually shows the cutting unit position as regards to
the stroke limits.
OPEN VICE (18) push it to open the vice then the led light flashes ( ex. when the cycle starts with open vice,
the vice will open again at the end of the cycle ).
CLOSE VICE (19) push it to close the vice. The same as above, that is, as for the
open vice.
CYCLE START(20) to start a semiautomatic cutting cycle. This intervention can be
no longer operative ( ex. when connecting the foot pedal ). The led light flashing indicates that machine is
working.
CYCLE STOP (21) it allows to stop the semiautomatic cutting cycle at any time and to push
the other keys.
FUNCTION 1 (26) when led light flashing , it allows the stroke return of the tool when the tool is in operation
; if led light is unflashing the tool is out of operation.
FUNCTION 2 (27) It does not work in this model because there is not the approaching phase.
FUNCTION 3 (25) if led light flashing, it finishes the semiautomatic cutting cycle at the end
of the cut .
TOOL SPEED 1 (11) if you push it when the motor is out of operation, it pre-select the lower cutting speed;
if you push it with the tool in motion it determines a speed reduction ( only for machines equipped with
inverter = ESC ) . Led light flashing means that the pre-selection has been made .
TOOL SPEED 0 (12) if you push it when the motor is out of operation , it pre-selects the speed 0 ( motor not
operating ) ; For reasons of security when machine is working the function is not operative.
Led light flashing indicates that pre-selection has been made.
TOOL SPEED 2 (13) by pushing it when machine is out of operation , it pre-selects the highest speed ; by
pushing it when the tool is in motion , it determines a speed increase ( only for machines equipped with
inverter = ESC ). Led light flashing indicates that pre-selection has been made.