background image

Dseries Harris J/S (JSC-2) Jog-Shuttle Control Panel  
Reference 

 

Unit Replacement 

 

Unit Replacement 

Notice to the Original Purchaser 

If this unit fails under normal use, and the unit is within the Standard Warranty period 
and/or is covered under a valid Support Contract with Imagine Communications, and 
Imagine Communications determines - in its sole discretion - that the product is 
defective, and provided that the purchaser returns the product, properly packaged 
and freight prepaid to Imagine Communications, Imagine Communications will - at its 
option - repair or replace the product. 

No warranty is implied or expressed as to the suitability of this product for a particular 
usage and Imagine Communications is not liable for any special, indirect, or 
consequential damages, however caused. 

To Return a Unit 

Follow this procedure when returning a defective unit for replacement. 

Stage 

Action 

Contact your Imagine Communications Representative to report the 
problem. 

Get an RMA number (Return Materials Authorization) for the unit from 
Imagine Communications. 

Request the proper “ship to” address:  

The Americas 

Europe, Asia, Africa 

Imagine Communications 

Automation  

9800 S. Meridian Blvd 

Englewood, CO  80112  USA 

Ph +1 303 476 5000 

Imagine Communications  

Automation 

Eskdale Road 

Winnersh Triangle 

Reading, Berkshire 

England  RG41 5TS 

Ph +44   (0) 118 9648189 

 

Repackage the unit and Ship To: the Imagine Communications office 
designated in stage 3. 

Imagine Communications will, at its option, repair or replace the product. 

 

© 2014 Imagine Communications Corp.     Proprietary and Confidential 

 9-April-2014  | Page 20 of 21 

Содержание 502072-00






















Отзывы: