Image Engineering LED-Panel V4 Скачать руководство пользователя страница 40

Страница: 40 / 44

Command Line Interface (CLI)

Examples

To set the LED switching time to 1/5000s call

LED-Panel.exe -setTime 15

To set the LED switching time to 1/125s call

LED-Panel.exe -setTime 38

6.2.26 Get LEDs Switching Time for the

“Exposure Time” Mode

Function

getTime

Description

With the function

“

LED-Panel.exe -getTime

“ it is possible to read the LED switching time of the

device in the "Exposure Time" mode.

Return parameters

After the execution of the command

“LED-Panel.exe -getTime“ the device will return a one- or

two-digits value XX of the switching time, where XX is the value of the switching time from the
Table 3.

For instance:

Return value

means that the switching time is 1/3200s.

6.2.27 Trigger iQ-Trigger (LED-Panel V4 only)

Function

setTrigger

Description

If a iQ-Trigger is connected to the LED-

Panel it can be triggered by using „

LED-Panel -

setTrigger <mode> -setTrigger <duration>

“

<mode>

Description

Standard mode

Power mode

Содержание LED-Panel V4













































Результаты поиска

Содержание LED-Panel V4

Отзывы:

Похожие инструкции для LED-Panel V4

Бренды по названию

Популярные бренды

Image Engineering LED-Panel V4, Руководство пользователя

Результаты поиска

Содержание LED-Panel V4

Отзывы:

Похожие инструкции для LED-Panel V4

Бренды по названию

Популярные бренды