Ilco Orion ECODRILL 2000 C/E Скачать руководство пользователя | Manualshive

Страница: 26 / 36

background image

Operating manual - English

ECODRILL 2000 C/E

27

8.5

Replacing the motor

Note: before carrying out any operations, disconnect the machine from the mains.

Replace the cutter motor in the way described below:
1) loosen the 6 screws (D1) and remove the top cover.
2) detach the 2 motor cables (D2) from the terminal board.
3) loosen the 4 screws (F1) securing the motor and remove the belt (F2).
4) unscrew the 4 screws (F1) completely and remove the motor.
5) unscrew the motor pulley (left-hand thread) and remove the pulley.
6) fit the pulley to the new motor.
7) secure the new motor with the 4 screws (F1) without tightening them.
8) tension the belt (pull the motor by hand) so that it is neither too tight or too loose and tighten the 4

screws (F1).

9) reconnect the 2 motor cables (D2).
10) replace the cover and secure with the 6 screws (D1).

Fig. 26

F1

F2

D2

«
...
24
25
26
27
28
...
»

Содержание ECODRILL 2000 C/E





































Отзывы:

Нет отзывов

Похожие инструкции для ECODRILL 2000 C/E

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: Campden instruments Страницы: 8

Бренд: Bacharach Страницы: 48

Бренд: Dana Design Страницы: 20

Бренд: ICP DAS USA Страницы: 45

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: Yamaha Страницы: 178

Бренд: Yamaha Страницы: 15

Бренд: Masalta Страницы: 13

Бренд: XPOtool Страницы: 4

Бренд: Harken Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды