ILC Dover S-5000 Series Скачать руководство пользователя страница 36

Страница: 36 / 40

- 35 -

S-2018

REV. D

STORAGE

Store your respirator at room temperature in a dry area that is protected from exposure to hazardous

contaminants.

TROUBLESHOOTING

Use the table below to help identify possible causes and corrective actions for problems you may experience.

Problem

Possible Cause

Corrective Action

Poor visibility through

visor

Visor is coated with debris.

Visor is scratched.

Wipe debris off.

Dispose of hood and replace it with new

hood.

Continuous low voltage

alarm sounds upon

blower activation

Battery is not charged.

Leave work area immediately.

Rechargeable Battery:

Switch to a fully charged battery, or

recharge.

Non-rechargeable Battery:

Replace Battery

Alkaline Battery Adaptor:

Install 5 new Duracell D-cell batteries

Low airflow

Battery needs charging.

Cartridges are loaded.

Filter plug not removed.

PAPR blower malfunction.

Leave work area immediately switch to fully

charged rechargeable battery, or a new non-

rechargeable battery.

Replace Cartridges.

Remove plug and install third CBRN filter.

Switch to a different blower unit.

Blower gasket is raised,

twisted, or has any

visible surface defects

Gasket is not properly seated

into the blower and may produce

a leak path

Contact ILC Dover Customer Service

Department immediately

1-800-631-9567

Blower housing is

cracked

Battery pack is cracked

Mishandling of the equipment

Improper use of the equipment

Excessive use/and or damage

Leave work area immediately and replace

with a new blower or battery pack.

Dispose damaged blower or battery and

replace.

Dents, Tears, Holes, or

Cracks in the Hood

Assembly or Breathing

Tube

Mishandling of the equipment

Improper use of the equipment

Not following the decon

procedures properly

Excessive wear/ and or damage

Leave work area immediately to prevent

contaminated air from entering the hood or

hose.

Dispose damaged hood or hose and replace it

with a new hood or hose.

Содержание S-5000 Series









































Результаты поиска

Содержание S-5000 Series

Отзывы:

Похожие инструкции для S-5000 Series

Бренды по названию

Популярные бренды

ILC Dover S-5000 Series, Руководство пользователя

Результаты поиска

Содержание S-5000 Series

Отзывы:

Похожие инструкции для S-5000 Series

Бренды по названию

Популярные бренды