IKELITE #0184.1
Silicone Lube
IKELITE #0184.1
Silicone Lube
3
4
SOS
Made in USA
Back View
Power: On/Off
Full
Power
Flashlight
1/4 Power
3/4
Power
1/2
Power
“
SOS” Mode
Fuel Guage
Indicator Light
Power
Switch
Power Settings
Flashlight (1/4 power) can be used
to conserve power when not
shooting video or shooting a very
close-up subject.
Full, 3/4, and 1/2 power are the
normal video shooting modes. Set
power accordingly based on
distance to subject, water clarity,
and ambient light.
“SOS” mode emits 3 short and 3 long
flashes, alternately. This is the
international distress signal and
should only be used in an
emergency.
PRO-2800 Package - System Assembly
1. First make sure you have all the components listed in your PRO-2800 Lite package -
Pages 4-5
.
2. Using a phillips screwdriver, attach the arm mount to the Lite Head if not already done -
Page 6
.
3. Remove Cord Protector Cap from Power Cord -
Page 6
. Lightly lube each Cord End o-ring. Use
only
Ikelite lube (supplied); other lubricants may cause the o-rings to swell and not seat properly.
Wipe off excess lube with a clean cloth. Make sure there is no hair or debris on the o-rings.
4. Attach one Cord End to the PRO-2800 Lite head -
Page 6, Diagram A.
Either Cord End can be
used.
5. Remove the Battery Pack from the Battery Pack Pouch.
6. Plug in the Smart Charger to fully charge your Battery Pack -
Page 8, Diagram D
.
7.
Attach the Battery Pack
to your specific system tray:
Page 9
for a Video Housing Tray,
Pages 10-11
for a DSLR Housing Tray, and
Page 13
for a Compact Video Dual Tray.
8.
Attach the PRO-2800
Lite with arm to your system:
Page 10
for a Video Housing,
Page 12
for a
DSLR Housing,
Pages 14-15
for Compact Video Housing.
9. Attach the remaining Power Cord End to a Battery Pack Female Connector.
10. Rotate Power Switch counter-clockwise to turn Lite on - see above.
PRO-2800 Operation & Power Settings
The PRO-2800 Lite features a rotational Power Switch. After the system is assembled and the
PRO-2800 is attached to a charged Battery Pack, rotate the switch counter-clockwise from the
On/Off position to your desired power setting. Rotate switch clockwise from your chosen power
setting to turn Lite off. Note that switch will NOT rotate clockwise past the On/Off position or
counter-clockwise past the “SOS” Mode position.
PRO-2800 Battery Capacity
Battery Capacity:
Fuel Guage Indicator Light Color = Capacity Remaining
-
GREEN = 100% (full charge) to 70% remaining power.
-
YELLOW = 69% to 40% remaining power.
-
RED = 39% to 10% remaining power.
-
RED BLINKING = 9% TO 0% power remaining.
When indicator light is blinking red, time remaining is approximately 10 minutes at full power. To
increase run time, decrease power level.
#6328.01 PRO-2800/SA-100 Ball-Socket Arm Package
PRO-2800 LED
Lite Head
SA-100 Ball
Socket Arm
Battery Pack with Pouch
Mounting Plate
E-clip: Qty. 2
Mounting Nut:
Qty. 2
1/4-20 x 1”
Flathead Screw:
Qty. 2 (Video)
1/4-20 x 5/8” Flathead
Screw: Qty. 2 (DSLR &
Compact Video)
Smart Charger with
4 adapter plugs
#6328.02 PRO-2800/Flex Arm Package
1/4-20 x 7/8”
Screw
Flex Mount
Shoulder Washer
E-clip: Qty. 2
Mounting Nut:
Qty. 2
1/4-20 x 5/8” Flathead
Screw: Qty. 2 (DSLR &
Compact Video)
1/4-20 x 1”
Flathead Screw:
Qty. 2 (Video)
Knurled Nut
PRO-2800 LED
Lite Head
Battery Pack with Pouch
Smart Charger with
4 adapter plugs
Mounting Plate
Lube
Included in Complete Package
Power Cord
Flex Arm
Cord
Cap
Power Cord
Cord
Cap
Lube
Included in Complete Package
